中财网猎头的发展方向:KAPAGEN的Tariel Kapanadze的发电机（自由能）
来源：百度文库 编辑：中财网 时间：2024/04/29 17:29:47
KAPAGEN的Tariel Kapanadze的发电机（自由能）
KAPAGEN, the Tariel Kapanadze's generator
by Jean-Louis Naudin
created on may 28, 2010 - JLN Labs - Last update July 5, 2010
Toutes les informati** et schémas sont publiés gratuitement ( freeware ) et sont destinés à un usage personnel et non commercial
All informati** and diagrams are published freely (freeware) and are intended for a *** use and a non commercial use.
The purpose of these series of experiments is to try to understand the working principle of the Tariel Kapanadze generator presented in his demo video and also to share in realtime the results of my findings through this web page.
WARNING !!!
Due to the presence of High Voltage and the High Power output of the Kapagen, users of this document should be very carefull and experienced in High-Voltage electronics to try anything out ! If you do it, the risk of any result is just yours. I take no resp**ibility of anything that might happen.
Testing such a device needs a lot of caution and the use of safety procedures, the experimenter must be very skilled in the use of High Voltage at High Power... PROJECT LOG BOOK
# 1 - June 9, 2010 - Kapagen replication by dragon
I've made several attempts with different coils and this is one of the better ones. The whole thing is Tesla basics as you can see in the diagram of the circuit. The picture's show it running a small 40 watt bulb at around 7 watts of input, the variac is set at around 50 volts. The NST is a 120V input with a 6500 volt .02 amp output. I have 2 earth grounds on this one but the second doesn't seem to add anything and can be removed without changing the light intensity or input requirement. One is required.
I've found by playing with various coils and bulbs it's not so much the wattage of the bulb in as much as the resistance of the bulb or bulbs. I have no real way of measuring the output at a wattage level, no claims are being made.... just an interesting experiment.
.....
Since I really don't know how JLN or Kapanadze is actually going about it I've been theroizing on my own of how to accomplish it and came to the conclusion it's nothing more than a reverse tesla coil. Instead of putting HV low amps into L1 and converting it to extreemly high voltage you do just the oposite... put the HV into L2 and convert it to lower voltage and higher amps through L1. The trick is getting L1 to resonate with L2 in its reverse form.
L1 being very low inductance using the earth ground through a load creates a psudo tank in which L1 can reach high amps. I still don't have the resonance dialed in quite right with this one although it seems to drive L1 reasonably well ( L1 being the 6 turn coil - L2 being the 90 turn coil - L3 the reversed 30 turn ). L3 is used to raise or lower inductance to help match the two. It might even help to make this one adjustable to some degree.
Getting bulbs to light is a matter of shuffling through various resistances to achieve the correct resp**e. I've run 175 watt mercury bulbs with it but those react like FL's and in my mind doesn't really c**titute wattage in as much as a voltage resp**e.
I've been doing some tests with a 150 watt halogen and it lights nicely produces lots of heat but is far from full bright. At 150 watt input it will be blindingly bright (sun like to your eyes), driving it with this set up it's bright but not blinding and is using about 35 watts to get it there although I can get an orange glow with lots of heat at 10 watts.
I need to do more work with this coil to dial in the resonance a bit better....
Fun stuff....
I am using 260w in the system and output is at least 500w.The bulbs are more than fully powered. After few more attempts I have destroyed 2 of them. I will have to get some more bulbs tommorow and see how many I can connect and still keep full brightness.I tryed to measure voltage across one bulb and it shows 335v-ac but all my meters are digital and I am sure it is not right.I need to get some analogic multimeters to find the amps and volts at the output.Few minutes ago I have started the system using DC to power the system an now I can see that DC is the only way to keep the system running for longer period of time.Using ac the spark gap becomes very hot as with dc it is much better.Also having a capacitor 90.02mf) connected in parallel with the load, keeps the flickering under control. I hope the picture attached will make all understand the basic of it.
I have posted another 2 video-clips testing circuit with high voltage AC then using DC as power source.
...
I am in UK, using 240vac. Every bulb is 100w and I have connected 9x100w. Sorry I forgot to show that in the video... I will do it next time.
I get around 1.6amp using AC to power the system but when I use DC it drops to around 1.15.
...
tube = 5.5cm/140cm - wire 4mm stranded except the big coil = 10mm stranded MOT I have no information about it. the tube is PVC 5mm thick I have no connection with J L Naudin.He lives in France, I live in London - UK, foreigner not British. I have a lot of respect for all his work. Everything he does is always well documented, tidy, showing a lot of knowledge in his work. I am very small comparing to him, many of us here are.I think that he is not trying to prove overunity with kapanadze replication, it is just showing proof of concept.Many applicati**. on J L Naudin website are proof of concept but enough to give us a start in many directi**. For J L Naudin free energy is a fact not just supposition. I am sure he has many devices built showing extra energy.
One thing I found is that you need both earth connecti** directly to the ground and about 10m distance. I didn't try longer distance as I don't have more lenght in the garden.In my first attempt I had one earth was comming from the water supply and the other one from a copper pipe I fixed in the ground.That showed me 2.3 amps for 500w load, then I have fixed another copper pipe in the ground at 10 m distance and I got about 1.6a for 900w load.MOT stays just a little bit warm in my case, maybe you have a defective MOT,run it without anything connected to see if it still gets hot, check capacitor value, if it is too high might create the problems you have.Not recommended to start the device inside the house as it will interfere with all electrical equipment, it does in my case, I have almost destroyed the tv, running the device in the garden.It is a lot of radio waves generated by the device and this is another problem at the moment.Turn off all electrical appliances in the house while testing.
Kapanadze replication v1.1 used 1.7A X 240ac = 408 watts input
Kapanadze replication v1.2 used 1.16A X 240ac = 281 watts input
Success all!
I am using two seperate grounds spikes and not the house ground.
Here is my first attempt, so don't laugh . I used a large variac on the 120vac input to the MOT (not shown). I had to work in the basement indoors so I used a copper water pipe feed for one ground and an iron floor drain pipe that leads outside & underground for the second. The spark gap is a non resistor sparkplug with a vice grip for a heat sink. The lamp is a 200watt 120 volt. I used the DC circuit with a small HV cap.
First results:
MOT gets very warm and the 20amp mains circuit breaker trips after 15 seconds of operation. Spark gap is electric blue, not violet. Please be careful with this circuit the voltages present are indeed dangerous.
Dave
Second attempt. After this mornings smoke test I almost gave up. Then there were some encouraging posts and advice. Here is some progress to report. I noticed on my set-up it works much better with high resistance loads. I started with two 40w light bulbs in series and then thought to try fluro tubes. I am up to six tubes in series with the two original 40w lamps. All the fluro tubes were removed from service a year or more ago as dim or non lighting. It reminds me of when many of us were adding LED's in series working with Dr. Stifflers SEC, what fun!
I have no way right now to measure input current. The voltage out of the variac is 90 volts. The spark has become very quiet with this load. I may post a short video on youtube later.
Hello romero and all
OK i am almost ready for a first test. I did the coil exactly as Romero that is 84 turns plus 22 turns plus 6 big turns.the coil 1 and 2 have the same stranded wire (blue) and for the big coil (green and yellow) there is 7 strand of plain copper, the center is made with 4 stranded copper and something torsaded for connection to one ground line, plus the main blue wire connection to the spark gap. the mot is rated 700 watts. I will use it directly (without the cap and diode for a first test. What do you think ? Or can i use the MO cap (0.95 micro farad and 2100 volts) and HV diode.?
I will ground it with 2 ground line conducting to 2 galvanised steel bar going 1 meter deep in the ground. and separated about 15 meter. I intend to use a wire with 3 time 1.5 mm2 bounded ,for the ground lines . I intend to begin with a halogen 500 watts what do you think ?
If it works, i will post the pictures of the c**truction of the coil step by step.
good luck at all
Laurent
# 7 - June 15, 2010 - Kapagen replication by woopy
Hello romero and all
OK i am almost ready for a first test. I did the coil exactly as Romero that is 84 turns plus 22 turns plus 6 big turns.the coil 1 and 2 have the same stranded wire (blue) and for the big coil (green and yellow) there is 7 strand of plain copper, the center is made with 4 stranded copper and something torsaded for connection to one ground line, plus the main blue wire connection to the spark gap. the mot is rated 700 watts. I will use it directly (without the cap and diode for a first test. What do you think ? Or can i use the MO cap (0.95 micro farad and 2100 volts) and HV diode.?
I will ground it with 2 ground line conducting to 2 galvanised steel bar going 1 meter deep in the ground. and separated about 15 meter. I intend to use a wire with 3 time 1.5 mm2 bounded ,for the ground lines . I intend to begin with a halogen 500 watts what do you think ?
If it works, i will post the pictures of the c**truction of the coil step by step.
good luck at all
Laurent
# 7 - June 15, 2010 - Kapagen replication by woopy
Hello romero and all
OK i am almost ready for a first test. I did the coil exactly as Romero that is 84 turns plus 22 turns plus 6 big turns.the coil 1 and 2 have the same stranded wire (blue) and for the big coil (green and yellow) there is 7 strand of plain copper, the center is made with 4 stranded copper and something torsaded for connection to one ground line, plus the main blue wire connection to the spark gap. the mot is rated 700 watts. I will use it directly (without the cap and diode for a first test. What do you think ? Or can i use the MO cap (0.95 micro farad and 2100 volts) and HV diode.?
I will ground it with 2 ground line conducting to 2 galvanised steel bar going 1 meter deep in the ground. and separated about 15 meter. I intend to use a wire with 3 time 1.5 mm2 bounded ,for the ground lines . I intend to begin with a halogen 500 watts what do you think ?
If it works, i will post the pictures of the c**truction of the coil step by step.
good luck at all
Laurent
Some numbers & a video.
MOT is a OBJY2
Input Voltage : 120vac
Input current : Measured at output of variac 4.0 amps avg
Load: Six 200w 120v Lamps
Earth Grounds : First: 200ft iron pipe (water well). Second: 10 ft driven rod, copper clad
Spark Gap : Champion J-14 with neo magnet attached
Air temperature was 68 degrees Fahrenheit
MOT Temp at start 84 F
MOT Temp at end 107 F
Run time approx 4.5 minutes
Hi all
the rain stopped shortly , and could not prevent me to have a second test.
Took all precaution as per Stefan and 3,2,1 go
yaouuh it works very fine. The bank directly connected to the grid does simply no light at all, but with the Kapagen it is near full brightness. i have AC current , no cap at all. I did not make any measure but the grid fuse did not even break. another thing i have a radio on at 10 meters from the kapagen and nothing , no grrrrrbbrrkkkkkk, at all in the radio.
OK and the rain comes again
hope that tomorrow it will be better weather to make some measurements.
just for info the bank as a resistance of 400 ohm. when i connect the bank to the grid, my clampmeter shows 130 ma at 230 volts AC just another thing the bank was on and stopped only when i switched off. but when i tried to take the measre of resistance it was impossible. Than i checked the bulb and one was broken. I mean it seems that i probably had the arc in the bulb which make the bulb on even if the tungsten filament is broken. What do you think?
good luck at all
Laurent
Dear Mr. Naudin,
Good news!
I got 1800W out and the MOT stays cold even the inlet power meter indicates 800W. I think that’s a real sign of OU. I have 2x150W halogen + 18x 100W bulbs (fully bright) and all serial. If I would have more lamps I think they would shine fully too.
I observed that with the 1N5408 diode didn’t work – but with the BY255 it works very well – just they get hot, so I add cooler.
I don’t know way you changed the coil setup but with the coil relation 22 – 84 – 6 its working quite well.
Many thanks and br.
Robert
Hi Guys!
I made a video of my setup, is my first one!
i putted some lamps of 60w others of 100w, all in series with a fan/ventilator of 100W... i putted the fan in the end of the sequence going to ground, because it haves a capacitor of 230V, i was affraid it can blow up if it takes all the primary voltage! 2 lamps in the video are not lighting well, but i think it was some problem with them!
this thing can feed all type of devices, not only lamps!
and it is not so spooky as at seems, when the adrenaline goes up, the fear fades! spectacular!
my output dont work well with dc, as you can see, dont used any caps!
dont took measurements because my DMM cannot read alternate current, only dc...
This vid is dedicated to the portuguese team in the worldcup, that win today 7-0 against North Korea
Enjoy!
All my thanks specially to JLNaudin, romerouk, laurent, xenomorph, jonny and the rest of the FE crew!
# 12 - June 25, 2010 - Kapagen successful replication by TomB-455
Dear Mr Naudin,
I have tried to replicate your coil and it works!
most of the setup is the same as yours, m.o.t. 800 watt, in dc mode. 10x150 wats halo-bulbs fully bright!!
i checkt my variac (but didn't put it on camera) and it was at 165 volts!!!
exept for the 23ccw turns on the entrance of the coil, those whre nessecery to reduce the input current.
the pictures are folowing soon. i did make a video though.. ;)
best regards,
TomB-455
I used for this setup; (V2)
M.O.T. 800 watt (D.C. setup),
10x150W halogen lamps(1500watt total) in series.
Variac 1,5kva.
Coil setup= prim.-88t(cw)+ 23t (ccw) , sec 7t(ccw).
The lamps are burning at 165 volts by 1.28 amps input on the 'kapagen' , these figures fluctuating in diffrence of +/- 5%
# 13 - June 28, 2010 - Kapagen successful replication by magnetflipper
This is an replication of J.L.Naudin's 'kapagen'.
I used for this setup; (V2)
M.O.T. 800 watt (D.C. setup),
10x150W halogen lamps(1500watt total) in series.
Variac 1,5kva.
Coil setup= prim.-88t(cw)+ 23t (ccw) , sec 7t(ccw).
The lamps are burning at 165 volts by 1.28 amps input on the 'kapagen' , these figures fluctuating in diffrence of +/- 5%
# 13 - June 28, 2010 - Kapagen successful replication by magnetflipper
I used for this setup; (V2)
M.O.T. 800 watt (D.C. setup),
10x150W halogen lamps(1500watt total) in series.
Variac 1,5kva.
Coil setup= prim.-88t(cw)+ 23t (ccw) , sec 7t(ccw).
The lamps are burning at 165 volts by 1.28 amps input on the 'kapagen' , these figures fluctuating in diffrence of +/- 5%
# 13 - June 28, 2010 - Kapagen successful replication by magnetflipper
This is an replication of J.L.Naudin's 'kapagen'.
I used for this setup; (V2)
M.O.T. 800 watt (D.C. setup),
10x150W halogen lamps(1500watt total) in series.
Variac 1,5kva.
Coil setup= prim.-88t(cw)+ 23t (ccw) , sec 7t(ccw).
The lamps are burning at 165 volts by 1.28 amps input on the 'kapagen' , these figures fluctuating in diffrence of +/- 5%
# 13 - June 28, 2010 - Kapagen successful replication by magnetflipper
This is an replication of J.L.Naudin's 'kapagen'.
I used for this setup; (V2)
M.O.T. 800 watt (D.C. setup),
10x150W halogen lamps(1500watt total) in series.
Variac 1,5kva.
Coil setup= prim.-88t(cw)+ 23t (ccw) , sec 7t(ccw).
The lamps are burning at 165 volts by 1.28 amps input on the 'kapagen' , these figures fluctuating in diffrence of +/- 5%
# 13 - June 28, 2010 - Kapagen successful replication by magnetflipper
This is an replication of J.L.Naudin's 'kapagen'.
I used for this setup; (V2)
M.O.T. 800 watt (D.C. setup),
10x150W halogen lamps(1500watt total) in series.
Variac 1,5kva.
Coil setup= prim.-88t(cw)+ 23t (ccw) , sec 7t(ccw).
The lamps are burning at 165 volts by 1.28 amps input on the 'kapagen' , these figures fluctuating in diffrence of +/- 5%
# 13 - June 28, 2010 - Kapagen successful replication by magnetflipper
Hi Mr. Naudin
The best (lowest input power) I could get was 707 Watts lighting 18 x 100 watt light bulbs without using a variac. It used 570 watts to light 9 of the 100 watt light bulbs.
I measured my power usage with a Kill-O-Meter connect to Mains over 30 feet away from my device.
When I first turned my Kapagen on it used over 1100 watts and the lights were approximately 50-60% bright. After playing with this for a week I got the power usage down to 707 Watts and the lights were at least 90% bright. I did this comparison by having one 100 watt light bulb connected to Mains sitting next to one of my light bulbs from my Kapagen. I agree it's not scientific but it was good enough for me to tell the difference.
But the most important thing I found was that the ground rods/connecti**/Earth was the biggest factor in lowering my power usage. I replaced my copper tube with c**truction grade grounding rods, applied water to the ground around my ground rods. In my area there is 6-12" of top soil and then under that it's all sand. Sand doesn't hold water very well.
Using Carbon rod and Copper for the spark gap lowered my input power usage by 55 watts.
My setup used 18 x 100 watt light bulbs totaling 1800 watts, serially connected, with 120 volt Mains input. The lowest wattage I could get without using a variac was 707 watts to light all 18 bulbs. It took 570 watts to light just 9 of the light bulbs. The difference between 9 bulbs and 18 bulbs was just an additional 137 watts (707 - 570 = 137 watts). The ground rods were 4 feet long and spaced over 35 feet apart. My device was placed closer to the South ground rod (~6 feet). I also had a ground plate of steel connected to the MOT.My Kapagen Device.
I tried varies spark gap materials and the copper & carbon combination lowered my power by 50 watts and produced a nice looking green spark.
Power used for all 18 x 100 watt light bulbs
Power used for 9 x 100 watt light bulbs
Toutes les informati** et schémas sont publiés gratuitement ( freeware ) et sont destinés à un usage personnel et non commercial
All informati** and diagrams are published freely (freeware) and are intended for a *** use and a non commercial use.
The purpose of this test is to measure with more accuracy the INPUT electrical power of the Kapagen v3.3. There are 14 x 150 W halogen lamps connected in serie at the output of the Kapagen. I have used a Voltcraft LX-1108 Luxmeter to measure the light intensity of one of these lamps Vs the electrical power required, a calibration curve has been set.
The Kapagen v3.3 Power IO results are below:
http://image.tech-domain.com/images/2010-10/kapagenv33IO.gif
See the video of this experiment:
June 30, 2010 - Power OUTPUT measured on the Kapagen v3.3
The purpose of this test is to measure the OUTPUT electrical power of the Kapagen v3.3. There are 14 x 150 W halogen lamps connected in serie at the output of the Kapagen. I have used a Voltcraft LX-1108 Luxmeter to measure the light intensity of one of these lamps Vs the electrical power required, a calibration curve has been set. So, it is easy to calculate the total power at the Kapagen output because the measured light intensity of the lamp is directly linked to the electrical power at the output. A calibration phase has been done with one of the 150 Watt halogen lamp used as the Kapagen load. The calibration lamp has been placed in a black box with the luxmeter probe. The 150 W lamp is connected directly to the Energy Check 3000 energy meter and connected to the variac (see the photos below).
Then the lamp has been reconnected to the Kapagen v3.3, and the light intensity is measured while the Kapagen is running.
The total OUPUT power for the 14 halogen lamps can now be easily calculated with the help of a spreadsheet.
It is important to notice that I have used the same energy meter for the calibration process than for the measuring the Kapagen power. You will also notice that the input power to light one halogen lamp is fully in line with its original specificati** (150 Watt of power at 220 V).
See the video of this experiment:June 22, 2010 - Very interesting test with the Kapagen v3.3
IMHO, I think that the working principle of the Tariel Kapanadze generator is to ** the free electr** from the Earth. The Earth is a big capacitor which contains free electric charges. If it is possible to create or to find a potential imbalance between two points in the ground, it seems possible to ** additional electr** from the ground and thus to create an increase of the current flow through a wire connected between these two points. Early in his researches in Colorado Springs, Nikola Tesla wanted to collect free energy from the Earth capacitor between the ground and the ionosphere by the use of a parametric resonance with the TMT project (read the Colorado Springs notes from 1899). Later, Tesla has also found that it is possible to do the same process with only the use of the ground by using the natural imbalance of the ground potential produced by the telluric currents flow underground and Tesla has found that this can be done by the use of an asymmetric displacement of current...
"Minimal work is done in the system due to absence of translational movement in the displacement current. As small heat losses occurs, oscillati** are maintained by the surplus charge stored in the coil. Very low energy expenditure allows power delivery to a load over an extended time period without an external fuel supply. After an initial input of energy from an outside source, Tesla's new electrical generator would operate as a fuelless device." from "The Second Law Thermodynamics and Tesla's Fuelless Generator" by Oliver Nichelson
Today, I am not able to say if my Kapagen v3.2 is fully in line with this principle above, because this is only the beginning of my research project, this is my main purpose and I explore this path as long as I continue to found something interesting, stay tuned...
To help me to find the imbalance of the ground potential on the surface of the Earth induced by underground telluric currents, I have built and I use a kind of surface tellurmeter (a low impedance electrometer), see a photo and the diagram of my device...From "The Second Law of Thermodynamics and Tesla's Fuelless Generator" by Oliver Nichelson
All the halogen lamps are protected by surge arrestors EPCOS 230V, this avoids to burn their tungsten filaments.
All the halogen lamps are protected by surge arrestors EPCOS 230V, this avoids to burn their tungsten filaments.
All the halogen lamps are protected by surge arrestors EPCOS 230V, this avoids to burn their tungsten filaments.
IMHO, I think that the working principle of the Tariel Kapanadze generator is to ** the free electr** from the Earth. The Earth is a big capacitor which contains free electric charges. If it is possible to create or to find a potential imbalance between two points in the ground, it seems possible to ** additional electr** from the ground and thus to create an increase of the current flow through a wire connected between these two points. Early in his researches in Colorado Springs, Nikola Tesla wanted to collect free energy from the Earth capacitor between the ground and the ionosphere by the use of a parametric resonance with the TMT project (read the Colorado Springs notes from 1899). Later, Tesla has also found that it is possible to do the same process with only the use of the ground by using the natural imbalance of the ground potential produced by the telluric currents flow underground and Tesla has found that this can be done by the use of an asymmetric displacement of current...
"Minimal work is done in the system due to absence of translational movement in the displacement current. As small heat losses occurs, oscillati** are maintained by the surplus charge stored in the coil. Very low energy expenditure allows power delivery to a load over an extended time period without an external fuel supply. After an initial input of energy from an outside source, Tesla's new electrical generator would operate as a fuelless device." from "The Second Law Thermodynamics and Tesla's Fuelless Generator" by Oliver Nichelson
Today, I am not able to say if my Kapagen v3.2 is fully in line with this principle above, because this is only the beginning of my research project, this is my main purpose and I explore this path as long as I continue to found something interesting, stay tuned...
To help me to find the imbalance of the ground potential on the surface of the Earth induced by underground telluric currents, I have built and I use a kind of surface tellurmeter (a low impedance electrometer), see a photo and the diagram of my device...
From "The Second Law of Thermodynamics and Tesla's Fuelless Generator" by Oliver NichelsonFrom "The Second Law of Thermodynamics and Tesla's Fuelless Generator" by Oliver Nichelson
The pulsed power is very strong and the use of halogen lamps is better than common incandescent lamps.
To work properly, the Kapagen requires two earth ground connecti** 10 meters spaced.
The power tapped depends on the weather conditi** and the underground current flow...
In the Kapagen v3.3, the spark gap has been improved and finely tuned.
The spark is very quiet and weak compared to the previous version with the tungsten rods.
The latest power input measurements is far more accurate than the previous, more tests must be soon conducted...
The purpose of the Kapagen is to ** the free electr** from the Earth. The Earth is a big capacitor which contains free electric charges. If it is possible to create or to find a potential imbalance between two points in the ground, it seems possible to ** additional electr** from the ground and thus to create an increase of the current flow through a wire connected between these two points.The Kapagen project is still under researches because its principle really worth to be deeply explored......
我也做过，没有成功，后来才知道那个线圈还需要一个谐振电路，让它共振起来才行，这个电路是kapangen的核心专利，没有公布。 交流电的功率用电压表和电流表分别测量，再相乘，缺少相位角的计算，可能得到的功率数偏大。
尤其是输出端，可能频率已经很高，电压电流表的误差也许很大了。
所以18楼第二图，用一个黑盒子，测量串联的相同灯泡中的一个 的 亮度。
预先用他那‘4000F型高端能量表’ 测出负载灯泡 功率-照度计读数 的关系曲线。
当灯泡用作负载时，还是读照度计读数，用预先的曲线反查得这个灯泡的功率，再乘负载灯泡个数，既得到比较准的总输出功率值。
电路元件好找在功放上都能找到呵呵！还现在想改改了
那个微波变压器功率太大，太危险了，所以不好测量了！其实卡伯珍我想也是这样的电路！这个电路可以驱动150W灯泡一个自供电！它的可以驱动5个好像100W吧不过没有这么亮
卡伯珍有可能是用的比这个功率大一点的的电路！希望各位有所启发吧
因为我也是业余的！没有多少经验的！呵呵！上面看电路图中的文字我给大家解释以下！
1.我想他线圈内部用的是45MM外径的环形铁氧体内径没有数据高为20MM，磁通量因数为u=2000网上卖 的我在淘宝看了就是有这种规格的价格最便宜的3.5元不过高为10MM的，PVC管我家的也是外径50MM的内径应该也就是47MM的吧！装置 要140MM的
要这个的铁氧体140/10=14 个，
2.它绕在铁氧体上的用高压激励的线圈线径没有给出，但图片可以看出1.5MM的喇叭线吧！给出的要绕PVC140MM，
3.调制线圈50HZ为38圈绕二层每层19匝
4。输出为220V50HZ线圈是要绕3层48匝，每圈16匝
像是高频变压器的反过来用一样的，
我想这装置的关键是铁氧体响应高频，前一章说的COP大于一的变压器就是因为
铁芯用了磁体吧！我想线圈的绕制只是变压！真正的还是铁氧体在起作用！
高压包高压脉冲直流线圈只是产生磁场！调制线圈产生了50HZ的磁通量！输出线圈看圈数来说不是共振的！只是耦合而已
这个装置可能就是利用磁能静脉冲发电的装置
我现在正在筹备这个装置的材料！等一到就要大干起来
前段时间用微波变压器作的实验我想就是误导别人
我的qq:312578603能和大家探讨！ 这个机器提取地下电能，如果大规模运用可能会破坏自然平衡，如同汲取地下水一样。 用黑白电视机高压包制作高压发生器http://wenku.baidu.com/view/a68b29bd960590c69ec376a2.html
怎么用彩电和黑白电视高压包改装高压发生电路 http://www.tudou.com/programs/view/HJnLv-8cqr8/
电路的重点是：1、降低频率；2、有效脉冲宽度
用集成块NE555改装的高压电路，优点频率可调，频宽可调555定时器频率计算http://www.838dz.com/calculator/1803.html参考：
555高压发生器电路原理
本高压发生器电路可产生稳定的8KV以上的高压，它电路简单，稳定可靠。该电路包括降压整流、稳压电路、18kHz多谐振荡器和升压变压器等，其电路如图所示。
降压整流电路由降压变压器T1和全桥整流器及滤波电容器C1等组成，整流出的15V直流电压，经三端稳压器7812稳压后输出+12v的稳定直流电压，为IC2、VT1等提供工作电压。
555和R1、R2、C3等组成一个无稳态多谐振荡器，其振荡频率为：
fc＝1.44/(R1+2R2)C3
图示参数是按18.5kHz设计的。
555输出的高频振荡脉冲经R3限流后，加至高频放大级VT1的基极。该放大器的负载是升压变压器T2，经T2的次级升压，可使次级输出达12KV的高压，再经高压堆或高压整流管整流后，可稳定输出+8KV的直流高压。
图中降压变压器T1的次级电压应不低于11V，功率不小于5VA；全桥整流器由四支1N4001组装而成，也可选用1A/400V的全桥模块；VT1可选用中功率高频开关管3DK106C或2SD1062等管型；升压变压器T2可使用14英寸电视机行输出变压器的磁芯和骨架，初级L1用Φ0.45高强度聚脂漆包线绕制54圈，次级用原高压包，无须改动。初级线圈绕制后最好烘干并腊封。参考：
555高压发生器电路原理
本高压发生器电路可产生稳定的8KV以上的高压，它电路简单，稳定可靠。该电路包括降压整流、稳压电路、18kHz多谐振荡器和升压变压器等，其电路如图所示。
降压整流电路由降压变压器T1和全桥整流器及滤波电容器C1等组成，整流出的15V直流电压，经三端稳压器7812稳压后输出+12v的稳定直流电压，为IC2、VT1等提供工作电压。
555和R1、R2、C3等组成一个无稳态多谐振荡器，其振荡频率为：
fc＝1.44/(R1+2R2)C3
图示参数是按18.5kHz设计的。
555输出的高频振荡脉冲经R3限流后，加至高频放大级VT1的基极。该放大器的负载是升压变压器T2，经T2的次级升压，可使次级输出达12KV的高压，再经高压堆或高压整流管整流后，可稳定输出+8KV的直流高压。
图中降压变压器T1的次级电压应不低于11V，功率不小于5VA；全桥整流器由四支1N4001组装而成，也可选用1A/400V的全桥模块；VT1可选用中功率高频开关管3DK106C或2SD1062等管型；升压变压器T2可使用14英寸电视机行输出变压器的磁芯和骨架，初级L1用Φ0.45高强度聚脂漆包线绕制54圈，次级用原高压包，无须改动。初级线圈绕制后最好烘干并腊封。参考：
555高压发生器电路原理
本高压发生器电路可产生稳定的8KV以上的高压，它电路简单，稳定可靠。该电路包括降压整流、稳压电路、18kHz多谐振荡器和升压变压器等，其电路如图所示。
降压整流电路由降压变压器T1和全桥整流器及滤波电容器C1等组成，整流出的15V直流电压，经三端稳压器7812稳压后输出+12v的稳定直流电压，为IC2、VT1等提供工作电压。
555和R1、R2、C3等组成一个无稳态多谐振荡器，其振荡频率为：
fc＝1.44/(R1+2R2)C3
图示参数是按18.5kHz设计的。
555输出的高频振荡脉冲经R3限流后，加至高频放大级VT1的基极。该放大器的负载是升压变压器T2，经T2的次级升压，可使次级输出达12KV的高压，再经高压堆或高压整流管整流后，可稳定输出+8KV的直流高压。
图中降压变压器T1的次级电压应不低于11V，功率不小于5VA；全桥整流器由四支1N4001组装而成，也可选用1A/400V的全桥模块；VT1可选用中功率高频开关管3DK106C或2SD1062等管型；升压变压器T2可使用14英寸电视机行输出变压器的磁芯和骨架，初级L1用Φ0.45高强度聚脂漆包线绕制54圈，次级用原高压包，无须改动。初级线圈绕制后最好烘干并腊封。 看了vfedtec.com/doc/kapanadze/kapanadze.pdf，Principle of work of Tariel Kapanadze's device老毛子写的，英文很烂。大概是说这玩意的原理是这样的：LC产生震荡对于自然界来说是一种不平衡，所以产生自感阻断这种变化，它说自感的能量从自然界中来，因此如果持续的让它不平衡就能摄取自然界能量。方法就是用L3连接L1和L2，做成混合的电路（否则就是变压器了）。然后不知道怎么的，L1、L2试图共振，并且试图跟地球环境共振并恢复平衡（这部分没看懂老毛子英文太烂），但是却被L3破坏了，环境中的能量源源不断进入L2，以使得L2能够恢复平衡。
所以：1.L1是初始振荡电路，必须尽量减少L1能量消耗，所以须用高电压、高频、小电流，所以要升高压，如果用超导，就不用升压了；
2.L2的频率必须与L1不同，并且要比L1匝数少，以获得大电流；
3.L1、L2、L3的频率要配比才能产生共振，然后获得最大能量（没看懂，不过我猜应该需要整数倍频率，因为交流电引起标量旋转变化需要频率整数倍，有点类似瑟尔那个幻方法则，可能是他们说的共振吧。不过更可能与WiTricity的非輻射性磁耦合(Nonradiative Magnetic Coupling)有关，也就是说输入电源的振荡频率应等于L2的固有振荡频率，但是L2是接地的，怎么算频率??）。
我发现图纸很多、很多，谁能给个自己验证过的、简单的当模型研究一下？我想算算频率的问题。我找到个老毛子的图纸，似乎是把地球也纳入了振荡系统。
又看了下kapanadze的专利，还是个国际专利WO2008103129A1，这里kapanadze有点作弊嫌疑，他把负载的L2线圈频率调整为220v-50Hz或110v-60Hz，我更确信他用了WiTricity的非輻射性磁耦合的原理，调成这两个频率真有点不厚道，无非就是抢输电线的电而已，传说**斯拉共振的是电离层。