北京金剪子服装:IBM/Brocade SAN 红皮书笔记3
来源:百度文库 编辑:中财网 时间:2024/04/20 13:02:34
第12章
12.1.1 Inter-switch links
ISL有3种方式:
◆ ISL R_RDY Mode : 用于取代Remote Switch
---> portcfgislmode 9,1
◆ Remote Switch:已被ISL R_RDY Mode取代
◆ Extended Fabrics
12.1.2 Buffer credit recovery
此功能仅用于8 Gbps switches
只支持长距离的GoldenEye2 and Condor2-based ports的E_Port
此功能不需要配置
12.1.3 Advantages of ISL Trunking
ISL Trunking 是b-type 系列交换机上可选组件
需要购买license
ISL Trunking 可将4个或8个ISL合并为单个链路
ISL Trunking使用Expansion Port (E_Port)
ISL Trunking 使用frame-level 负载均衡
当一个master link offline时,会自动选择新的master link,不会中断传输
Trunk ports:
◇ 必须是E_Ports or EX_Ports
◇ Trunk ports必须运行在相同的速度
◇ 每个交换机都要安装trunking license
◇ 交换机之间的trunk线缆长度要小于500m
Trunk masters:
◇ 用于定义trunk group
◇ 每个trunk group有一个trunk master和几个trunk subordinate link
ISL Trunking Telnet commands
GUI ---> 选中端口 ---> Enable Trunking 或 Disable Trunking
P462---P496
12.1.4 Fabric Interoperability trunking
不支持在FOS和M-EOS之间进行trunk
Long distance
在不同的模式下对license有不同需求
---> portCfgLongDistance
L0: 正常值,禁用long distance
LE: 10km
L0.5 : <25 km
L1 : <50km
L2 : <100km
LD :
LS :
12.2 Merging fabrics
通过ISL连接多个SAN,形成一个大的fabric
添加交换机到现有的fabric之前要disable交换机:可避免Domain ID冲突,将交换机disable后接入fabric,再enable,会自动协商Domain ID,并设置有效值
Domain ID用来标识交换机,在fabric中每个交换机的Domain ID必须唯一
---> switchDisable
---> configure
Fabric Manager ---> Tasks → Fabric Management → Fabric Merge Check
合并SAN:
如果两个交换机在合并时有冲突(?),会先offline一个交换机,合并后再online
用ISL连接多台交换机
ISL Trunking增加带宽
13:14 2009-6-29
第13章
Secure Fabric OS是可选组件,需license
FOS 6.X不再支持Secure Fabric OS
Secure Fabric OS只能用于FOS 5.3及以前版本
Secure Fabric OS使用数字证书
Fabric Manager会自动将交换机密码存储在服务器上(默认)
当disable此功能后,重启client需要再次monitor fabric
FM
--->Edit
--->Preferences
--->General
--->Persist switch passwords 默认为勾中,即启动此功能
FM
---> Tasks
→ Switch Management
→ Set Admin Password
选中多台交换机,更改密码
在status列中:黄色---正在设置新密码
默认时,所有交换机使用HTTP来管理
FM每30分钟更新一次Admin Domain信息,刷新Fabric Data不会更新Admin domain信息
256个Admin domain(0—255)
未看完
11:12 2009-6-30
第14章
Adaptive Networking :优化SAN的一套工具
◇ Traffic Isolation:支持4G/8G交换机,无需license
◇ Quality of service (QoS) Ingress Rate Limiting:只支持8G交换机,需要license
◇ QoS SID/DID Traffic Prioritization:只支持8G交换机,需要license
14.1 Traffic Isolation
用于控制交换机之间的传输,使用专用的N_port建立一个专用路径来传输数流
Traffic Isolation使用专用的zone, 叫做Traffic Isolation zone (TI zone)
使用F_Port和E_port
14.1.1 Creating a TI zone
---> zone --create -t objtype [-o optlist] name -p “portlist”
---> zone --create -t ti ti_host1 -p "1,29; 1,30; 1,0;2,2;2,5; 4,6; 4,12; 4,13"
---> cfgenable "FabricA_Cfg"
14.1.2 TI zone failover
14.1.3 FSPF routing rules and traffic isolation
所有的传输必须使用低成本的路径All traffic must use the lowest cost path.
未看完
第15章
一些高级功能只能使用CLI
Web Tools ---> Performance Monitor
性能监控每30秒更新一次
保存自定义的监控:File → Save Current Canvas Configuration
调用自定义的监控:File → Display Canvas Configurations
基本的性能监控:不需要license
Web Tools ---> Performance Graphs → Basic Monitoring
◇ Port Throughput : 选中一个端口,查看端口吞吐量
◇ Switch Aggregate Throughput: 交换机所有端口总的吞吐量
◇ Blade Aggregate Throughput:仅对SNA768B和SAN256B有用;
显示某个blade的吞吐量
◇ Switch Throughput Utilization:显示各端口的吞吐量利用率
◇ Port Error:显示端口的CRC错误量
◇ Switch Percent Utilization:类似于Switch Throughput Utilization,但显示的是百分比
◇ Port Snapshot Error:
P655
高级性能监控:需要license
◇ SID/DID Performance:在源ID和目标ID对之间的传输;
要选正确的SID,DID,Switch Port
◇ SCSI Commands: 显示每个交换机端口或端口上指定LUN的读/写命令的数量
◇ SCSI versus IP Traffic:端口上IP和SCSI传输量的百分比
◇ ALPA Error: 用在旧的交换机上
P663---P677
15.2.1 End-to-end monitoring
在SID和DID之间的FC frame的传输量
---> perfAddEEMonitor
15.2.2 Displaying the end-to-end mask of a port
15.2.3 Filter-based monitoring
15.2.4 ISL monitoring
15.2.5 Top Talkers monitoring
15.2.6 Trunk monitoring
15.2.7 Saving and restoring monitoring configuration
一般的监控在WEB TOOLS中用图形方式显示
高级监控需要license,用CLI (未看)
15:58 2009-6-29
第16章
确保SAN健康和排错
16.1 SAN Health
SAN Health :此工具用于管理和优化SAN
两种机制:
back-end reporting processor
front-end data collection agent
前端收集数据
后端处理
下载并安装SAN Health
将收集到的数据通过SAN Health发送到Brocade Wet Site,24小时内会收到结果
收到的结果是2个文件: 一个visio连接图
16.2 Error logs
3种错误日志:
◇ TraceDump: 复制内存到一个文件中
◇ RASLOG: 包含交换机的debug数据
◇ supportShow: 交换机的状态和配置信息
16.2.1 Capturing a trace dump
……
P700
FM → Tasks → Capture Technical Support Information
--->supportShow
--->supportSave
16.2.3 General device health
FM → Tasks → Device Management and Troubleshooting → Device Connectivity Trouble Shooting
16.2.4 Trace route
路由路径信息
FM → Tasks → Device Management and Troubleshooting → Trace Route
16.2.5 Fabric merge
检查fabric合并时是否有冲突
FM → Tasks → Fabric Management → Fabric Merge Check
16.3 Port Fencing
Fabric Operating System v6.1 (Fabric OS) adds a new feature called Port
Fencing, which disables a port automatically when it is operating outside the
bounds of normal operation.
E, F, and FL port types are port classes supported by port fencing, and we can
enable the port fencing for these port classes only.
---> fwconfigure
---> switchShow
16.4 Command output enhancement
---> switchshow |more
16.4.1 Basic troubleshooting commands基本的排错命令
chassisShow
diagShow
errDump
errshow
fabStatsShow
fanShow
fcPing
islShow
portCfgShow
portErrShow
portLogShow
portShow
portStatsShow
psShow
supportshow
switchShow
topologyShow
---> help
9:24 2009-6-30
P28
在Web Tools中可查看,升级FOS
P29
Brocade Access Gateway Administrator's Guide
P31
fabric OS native
fabirc OS open
M-EOS native
M-EOS open mode
P32/33
P32
CHAPTER 2
P45
对本章内容没能深入了解
是否是讲用 SAN768B (Brocade DCX Backbon)来构建存储虚拟化???
CHAPTER 3
P56
P57
用4/8个端口做ISL Trunk Group,负载匀衡
P70
P73
P75
P80
P81
P82
P86
SAN256B
CHAPTER 4
Access Gateway
FC4-16IP------16个iSCSI端口 ???
FICON
Fabric OS的升级,降级,备份
CHAPTER 6
设置交换机时间日期
--->date “MMDDhhmmYY”
P122
SAN768B的logical switch SW0上没有默认IP
P125 用ipAddrSet设置交换机IP时
Fibre Channel IP Address [none]:
P128
---> ipAddrSet –sw 0
P130
在用telnet连接到交换机时,命令是否区分大小写 ???
CHAPTER 8
Web Tools需要JAV 1.6, IE 7
CHAPTER 11
P423
P425
--->最大zoning database是多大???
P438
P450
CHAPTER 12
在实际应用中,如果2个独立的SAN合并为一个大的fabric,可能会有一些配置冲突,如何解决这些冲突,未看明白