i5主板推荐:Parlor Article--Floor

  ================================================== ================
[Concept]
    Buildings on the ground surface, by the board or other surface material made of
================================================== ================
[] Wood floor maintenance
    On the wood floor maintenance and repair must be able to "second ground", and "avoid."
--------------------------
* [Ground lighting candle]
    Waxing the floor of the wood better protection, but also increase the floor finish.
--------------------------
* [Ground view of humidity]
    During the winter indoor temperatures are high, the air drier, should increase the humidity, such as the basin of water placed in the room can also use a humidifier; rain for a long time, air humidity, ventilation, windows should be.
--------------------------
* [Avoid repair back up]
       Paved flooring, cracks will appear as a variety of reasons, degumming, warping, loose and so, once found in the individual floor deformation, deformation should be considered the cause and laying methods (pick or nail glue) promptly repair or replacement.
--------------------------
* [Avoid very hot exposure]
    Please do not pay attention to cigarette butts, stoves and heaters placed directly on the wooden floor, to prevent burning out the scars and burning fire.
--------------------------
* P Pharmacy avoid pouring wine]
    Do not soy sauce, wine and beverage pH solvents or chemicals spilled on the wooden floor.
--------------------------
       Spring dry climate, coupled through a winter heating baking, more likely to lead to indoor air drying in order to allow the floor "skin" more moisture, increasing the number of floor wax to extend its life into many people's choice.
Suitable for floor waxing can play moisture, damage, increase the surface brightness and easy to clean effect, but if the wax too frequently, will cause damage to the floor. Frequent waxing will cause wax scale wax layer stack, and there will be two intermediate gray layer of wax, waxing influence results.
At present, more and more families laying laminate flooring, laminate flooring surface as wear-resistant paper, composed of "aluminum oxide", which metal layers so that the wax can not penetrate to the floor inside, only attached to the floor surface. After waxing, people will leave footprints when walking a long time as the floor surface to become the "big face" in general, affect the appearance and difficult to wipe the floor care.
Can be wrung cloth wipe, and then maintenance care solution, it is difficult to wipe the place with special cleaning agents to remove.
================================================== ================
[Elements] buy
1, to see the brand
    Brand goods in order to ensure its products, equipment, technology, technical staff, pre-sales, service brand quality, large manufacturers do not dare to drop their own brand.
2, see the tree material
       In general, wood density, the higher the greater the proportion of oily medium, the greater the intensity, quality, and better. Mentioned earlier, various types of imported or domestic species such as Balsamo, incense two winged beans, heavy wood ants, fiber skin Lecythidaceae, teak, picking sub-trees, dipterocarp, etc. for high-grade species. Floor should be purchased from the color, smell identification, to see whether the dead section, mixed, cracking, mildew and other defects.
3, see the size
       Write down the best wood flooring standard (unit: mm): Length: 606 (610), 758 (760), 910 (909), 1200, etc.; Width: 93,125 (123/128); thickness: 18. Of course, buy the floor should be chosen according to their own, not on the pursuit of long, wide floor. Length, width is too large, loss is also large, relatively greater degree of deformation.
4, to see whether the moisture content of the floor of 8% to 14% within.
5, to see with precision
    Take eight hand stitching around the floor, check for tight, smooth, the thickness is uniform.
6, to see the film is full, even thick, no bubbles, leakage gap, etc., and then try to film the degree of wear.
7, the correct view of color problems
       Solid wood flooring is made of natural wood processing, wood lumber by the light, regional water and soil, environmental impact, there is normal color, can be adjusted to achieve satisfactory results, without demanding a small color difference. But also to prevent the individual businesses of different species, different levels of flooring mixed, consumer fraud, it's best to consult the industry.
8, solid wood flooring has become a "luxury" accessories, please buy Which Which flooring is best installed to avoid future wrangling.
================================================== ================
[Troubleshooting]
--------------------------
First, the seams from the drum
A, the floor surface of the water
       Installation process, the inevitable and sometimes glue joints are not completely filled. If the mop when mopping the floor surface can cause dripping and water from entering the seams less sizing, floor substrate will absorb moisture, resulting in local swelling and a small bubble from the phenomenon. This partial surface of the floor seams muster;
B, from the dark water below the floor
       Shape of the surface phenomena of a more uniform seams muster, from the water near the place heavier strict, far more level. Where such problems are: close to the bathroom, kitchen, heating pipes, air conditioning condensate discharge port, windows, etc.. Such as flooding a long time, the symptoms have been obvious, to open the floor to check the watermark to determine the cause;
C, short-floor joints from drum
    Performance of the short side of each strip flooring seams are from the dark, the ground is usually caused by too much moisture. Muster higher, indicating greater ground moisture.
    Maintenance program: replacement of the floor.
--------------------------
Second, the floor bagging
    Phenomenon is a step up the performance a sense of suspension, in some places would be more serious.
A, lack of expansion joints aside, the floor bagging;
B, spread through the room
       More than two rooms in the installation does not install the floor when the button bar at the Door, in the moisture, moisture is large two-room floor, horizontal stretch, causing the room door to each other involved, so that the floor bagging;
C, expansion joints to be crucified or baseboard plaster, putty and other fill, so the floor can not be extended, leading to the floor bagging;
D, the installation process, a foreign body left on the floor, resulting in bagging;
E, primary bagging floor, such as the installation before the original ground floor has wood flooring, floor Zhuangwan after bagging a result of the original floor damp, causing the floor to be arch;
       Maintenance program: from under the skirting board, once again reserved for expansion joints; connection in the room and room to install buckle of; re-install the baseboard, clean out the plaster, putty, etc. reserved for expansion joints; from the open floor, re-fill equipment; split off the floor, ground handling flat, dry and re-paving the floor.
--------------------------
Third, the floor cracks
A, uneven ground
    In the case of uneven ground, paving the floor, use a period of time, the gap between the floor glue have torn off;
B, small sizing
    Floor in the winter, a heated baking, air dry, flat floor contraction, insufficient glue joints, strong enough, so that the floor cracked open the plastic seam produced;
C, on the edge of a heavy
       Need to repair the floor opposite the direction parallel to the heavy pressure, so the floor can not be free to shrink, resulting in cracks; this room there will be bagging phenomenon in the summer, and winter heating, cracks will come when the phenomenon;
       Maintenance program: removed the floor, ground handling smooth, dry pavement again; according to the size of cracks, the decision up wax, re-potting; fixed with special tools or heavy equipment; away the heavy, re-filling glue.
--------------------------
Fourth, surface defects
A, off angle
    Bump the floor in the handling process, the process of construction workers in the construction or construction not pay attention to cleaning up after a bad glue when the shovel, so that the corners are off the floor angle phenomenon;
B, surface loss
       After construction, sharp or heavy objects fall smashed the floor, the floor beautiful affected; or floor process, not glued substrate surface with good use for some time,
Degumming with the substrate surface;
C, scratches
    Customers place on the floor move furniture or heavy objects, the objects between floor and sand mixed with nails or other debris on the floor and drag floor caused significant damage or wear-resistant layer of scratches;
    Maintenance program: repair or replacement of floor wax block.
--------------------------
Fifth, the floor smirch:
    Floor of a large area smirch, and difficult to clean.
A, because the performance of the floor structure of the causes of the scar can not be cleaned;
B, the performance of sealed floor is bad, can not afford to clean up after penetration of the stain, causing the surface of black spots or black lines;
    Maintenance program: brush cleaning by professionals with the maintenance of the floor and take the right approach; in the case of quality problems, replace the floor in question.
--------------------------
Sixth, skirting board problem
A, bagging
    Damp or wet weather causes the wall, skirting no telescopic expansion space;
B, Interface uneven
    Uneven ground or not carefully installed the interface caused by a high degree of inconsistency;
C, and the walls, cabinets and other facade cracks: the wall is uneven or nails irrational;
D, the gap with the ground
    Mainly caused due to uneven ground;
    Maintenance program: from under the skirting board, re-processing installation, fill putty and so on.
--------------------------
Seven questions buckle
A, loose
    Careless or buckle due to the construction of the screw and the base was not complete and other reasons;
B, fracture warp: deduction of inferior quality;
C, and the door pockets are not parallel: installing careless or set aside the original location of the customer is not parallel, the construction workers did not pay attention to cause
==================================================

【Article is excerpted from: Baidu Encyclopedia】
【Network reprint / Just reference】
【Translation is by Goolge】