保定职业技术学院oa:机械行业专业术语11
来源:百度文库 编辑:中财网 时间:2024/05/04 05:59:09
组装、冲压、喷漆等专业词汇
Assembly line 组装线 Layout 布置图
Conveyer 流水线物料板 Rivet table 拉钉机
Rivet gun 拉钉枪 Screw driver 起子
Electric screw driver 电动起子Pneumatic screw driver 气动起子
worktable 工作桌 OOBA 开箱检查
fit together 组装在一起 fasten 锁紧(螺丝)
fixture 夹具(治具) pallet 栈板
barcode 条码 barcode scanner 条码扫描器
fuse together 熔合 fuse machine 热熔机
repair 修理 operator 作业员
QC 品管 supervisor 课长
ME 制造工程师 MT 制造生技
cosmetic inspect 外观检查 inner parts inspect 内部检查
thumb screw 大头螺丝 lbs. inch 镑、英寸
EMI gasket 导电条 front plate 前板
rear plate 后板 chassis 基座
bezel panel 面板 power button 电源按键
reset button 重置键 Hi-pot test of SPS 高源高压测试
Voltage switch of SPS电源电压接拉键 sheet metal parts 冲件
plastic parts 塑胶件 SOP 制造作业程序
material check list 物料检查表 work cell 工作间
trolley 台车 carton 纸箱
sub-line 支线 left fork 叉车
personnel resource department人力资源部production department 生产部门 planning department 企划部QC Section 品管科
stamping factory 冲压厂painting factory 烤漆厂
molding factory 成型厂common equipment 常用设备
uncoiler and straightener 整平机punching machine 冲床
robot 机械手hydraulic machine 油压机
lathe 车床planer ('plein);|刨床
miller 铣床grinder 磨床
driller 钻床linear cutting 线切割
electrical sparkle 电火花welder 电焊机
staker=reviting machine 铆合机position 职务
president 董事长 general manager 总经理
special assistant manager 特助factory director 厂长
department director 部长deputy manager | =vice manager 副理
section supervisor 课长deputy section supervisor =vice section
superisor 副课长group leader/supervisor 组长
line supervisor 线长assistant manager 助理
to move, to carry, to handle 搬运be put in storage 入库
pack packing 包装to apply oil 擦油
to file burr 锉毛刺final inspection 终检
to connect material 接料to reverse material 翻料
wet station 沾湿台Tiana 天那水
cleaning cloth 抹布to load material 上料
to unload material 卸料to return material/stock to 退料
scraped |'skr?pid|报废scrape ..v.刮;削
deficient purchase 来料不良manufacture procedure 制程
deficient manufacturing procedure 制程不良
oxidation |' ksi'dei?n|氧化scratch 刮伤
dents 压痕defective upsiding down 抽芽不良
defective to staking 铆合不良embedded lump 镶块
feeding is not in place 送料不到位stamping-missing 漏冲
production capacity 生产力education and training 教育与训练
proposal improvement 提案改善spare parts=buffer 备件
forklift 叉车trailer=long vehicle 拖板车
compound die 合模die locker 锁模器
pressure plate=plate pinch 压板bolt 螺栓
name of a department 部门名称
administration/general affairs dept 总务部automatic screwdriver 电动启子
thickness gauge 厚薄规gauge(or jig)治具
power wire 电源线buzzle 蜂鸣器
defective product label 不良标签identifying sheet list 标示单
screwdriver holder 起子插座pedal 踩踏板
stopper 阻挡器flow board 流水板
hydraulic handjack 油压板车forklift 叉车
pallet 栈板glove(s)手套
glove(s) with exposed fingers 割手套thumb 大拇指
forefinger 食指midfinger 中指
ring finger 无名指little finger 小指
band-aid 创可贴iudustrial alcohol 工业酒精
alcohol container 沾湿台head of screwdriver 起子头
sweeper 扫把mop 拖把vaccum cleaner 吸尘器
rag 抹布garbage container 灰箕
garbage can 垃圾箱garbage bag 垃圾袋
chain 链条jack 升降机
production line 流水线chain 链条槽
magnetizer 加磁器lamp holder 灯架
to mop the floor 拖地to clean the floor 扫地
to clean a table 擦桌子air pipe 气管
packaging tool 打包机packaging 打包
missing part 漏件wrong part 错件
excessive defects 过多的缺陷critical defect 极严重缺陷
major defect 主要缺陷minor defect 次要缺陷
not up to standard 不合规格dimension/size is a little bigger 尺寸偏大(小)
cosmetic defect 外观不良slipped screwhead/slippery screw head螺丝滑头
thread 滑手speckle 斑点mildewed=moldy=mouldy 发霉
rust 生锈deformation 变形burr(金属)flash(塑件)毛边
poor staking 铆合不良excesssive gap 间隙过大
grease/oil stains 油污inclusion 杂质
painting peel off 脏污shrinking/shrinkage 缩水
mixed color 杂色scratch 划伤
poor processing 制程不良poor incoming part 事件不良
fold of pakaging belt 打包带折皱painting make-up 补漆
discoloration 羿色water spots 水渍polishing/surface processing 表面处理
exposed metal/bare metal 金属裸露lack of painting 烤漆不到位
safety 安全quality 品质
delivery deadline 交货期cost 成本
engineering 工程die repair 模修
enterprise plan = enterprise expansion
projects 企划QC 品管
die worker 模工production, to produce 生产
equipment 设备to start a press 开机
stop/switch off a press 关机classification 整理
regulation 整顿cleanness 清扫
conservation 清洁culture 教养
qualified products, up-to-grade
products 良品
defective products, not up-to-grade products 不良品
waste 废料board 看板feeder 送料机
sliding rack 滑料架defective product box 不良品箱
die change 换模to fix a die 装模
to take apart a die 拆模to repair a die 修模
packing material 包材basket 蝴蝶竺
plastic basket 胶筐isolating plate baffle plate; barricade 隔板
carton box 纸箱to pull and stretch 拉深
to put material in place, to cut material,to input 落料
to impose lines 压线to compress, compressing 压缩
character die 字模to feed, feeding 送料
transportation 运输(be)qualfied, up to grade 合格
not up to grade, not qualified 不合格
material change, stock change 材料变化feature change 特性变更
evaluation 评估prepare for, make preparations for 准备
parameters 参数rotating speed, revolution 转速
manufacture management 制造管理
abnormal handling 异常处理
production unit 生产单位
lots of production 生产批量steel plate 钢板roll material 卷料
manufacture procedure 制程operation procedure 作业流程
to revise, modify 修订to switch over to, switch---tothrow--over switching over 切换
engineering, project difficulty工程瓶颈stage die 工程模
automation 自动化to stake, staking, reviting 铆合
add lubricating oil 加润滑油shut die 架模
shut height of a die 架模高度
analog-mode device 类模器
die lifter 举模器argon welding 氩焊
vocabulary for stamping
冲压常词汇
stamping, press 冲压punch press, dieing out press 冲床
uncoiler & strainghtener 整平机feeder 送料机
rack, shelf, stack 料架cylinder 油缸
robot 机械手taker 取料机
conveyer belt 输送带
transmission rack 输送架top stop 上死点
bottom stop 下死点one stroke 一行程
inch 寸动to continue, cont.连动to grip(material)吸料
location lump, locating piece, block
stop 定位块reset 复位
smoothly 顺利dent 压痕
scratch 刮伤deformation 变形
filings 铁削to draw holes 抽孔
inquiry, search for 查寻to stock, storage, in stock 库存
receive 领取approval examine and verify 审核
processing, to process 加工delivery, to deliver 交货
to return delivenry to./to send delinery back/to retrn of goods 退货
registration 登记registration card 登记卡
to control 管制to put forward and hand in 提报
safe stock 安全库存acceptance = receive 验收
to notice 通知application form for purchase 请购单
consume, consumption 消耗to fill in 填写
abrasion 磨损reverse angle = chamfer 倒角
character die 字模to collect, to gather 收集
failure, trouble 故障statistics 统计
demand and supply 需求career card 履历卡
to take apart a die 卸下模具to load a die 装上模具
to tight a bolt 拧紧螺栓to looser a bolt 拧松螺栓
to move away a die plate 移走模板
easily damaged parts 易损件standard parts 标准件
breaking.(be)broken,(be)cracked 断to lubricate 润滑
common vocabulary for die
engineering
模具工程常用词汇
die 模具figure file, chart file 图档
cutting die, blanking die 冲裁模
progressive die, follow (-on)die连续模
compound die 复合模punched hole 冲孔
panel board 镶块to cutedges=side cut=side scrap 切边
to bending 折弯to pull, to stretch 拉伸
Line streching, line pulling 线拉伸engraving, to engrave 刻印
upsiding down edges 翻边to stake 铆合
designing, to design 设计design modification 设计变化die block 模块
folded block 折弯块sliding block 滑块location pin 定位销
lifting pin 顶料销die plate, front board 模板padding block 垫块
stepping bar 垫条upper die base 上模座lower die base 下模座
upper supporting blank 上承板upper padding plate blank 上垫板
spare dies 模具备品
spring 弹簧bolt 螺栓document folder 文件夹
file folder 资料夹to put file in order 整理资料
spare tools location 手工备品仓first count 初盘人
first check 初盘复棹人second count 复盘人
second check 复盘复核人equipment 设备
waste materials 废料work in progress product 在制品
casing = containerazation 装箱quantity of physical invetory second
count 复盘点数量quantity of customs count会计师盘,点数量
the first page 第一联filed by accounting department for reference 会计部存查
end-user/using unit(department) 使用单位
summary of year-end physical inventory bills年终盘点截止单据汇总表
bill name 单据名称
This sheet and physical inventory list will be sent to accounting department
本表请与盘点清册一起送会计部-
department together (Those of NHK will be sent to financial(NHK 厂区送财会部)
Application status records of year-end physical inventory List and physical inventory card 年终盘点卡与清册使用-状况明细表
blank and waste sheet NO.空白与作废单号plate 电镀
mold 成型material for engineering mold testing
工程试模材料
not included in physical inventory 不列入盘点sample 样品
incoming material to be inspected 进货待验description 品名
steel/rolled steel 钢材
material statistics sheet物料统计明细表meeting minutes 会议记录
meeting type 会别distribution department 分发单位
location 地点chairman 主席
present members 出席人员subject 主题conclusion 结论
decision items 决议事项responsible department 负责单位
pre-fixed finishing date 预定完成日approved by / checked by / prepared by核准/审核/承办PCE assembly production schedule sheetPCE 组装厂生产排配表
model 机锺work order 工令revision 版次
remark 备注production control confirmation 生产确认
checked by 初审approved by 核准
department 部门stock age analysis sheet库存货龄分析表
on-hand inventory 现有库存available material 良品可使用
obsolete material 良品已呆滞to be inspected or reworked待验或重工
total 合计cause description 原因说明
part number/ P/N 料号type 形态
item/group/class 类别quality 品质prepared by 制表
notes 说明year-end physical inventory difference analysis sheet年终盘点差异分析表physical inventory 盘点数量physical count quantity 帐面数量difference quantity 差异量cause analysis 原因分析
raw materials 原料materials 物料
finished product 成品semi-finished product 半成品
packing materials 包材good product/accepted goods/ accepted
parts/good parts 良品defective product/non-good parts 不良品
disposed goods 处理品warehouse/hub 仓库
on way location 在途仓oversea location 海外仓
spare parts physical inventory list 备品盘点清单
spare molds location 模具备品仓skid/pallet 栈板
tox machine 自铆机wire EDM 线割
EDM 放电机coil stock 卷料
sheet stock 片料tolerance 工差
score=groove 压线cam block 滑块
pilot 导正筒trim 剪外边
pierce 剪内边drag form 压锻差
pocket for the punch head 挂钩槽slug hole 废料孔
feature die 公母模expansion dwg 展开图
radius 半径shim(wedge)楔子
torch-flame cut 火焰切割set screw 止付螺丝
form block 折刀stop pin 定位销
round pierce punch=die button 圆冲子shape punch=die insert 异形子
stock locater block 定位块under cut=scrap chopper 清角
active plate 活动板baffle plate 挡块
cover plate 盖板male die 公模
female die 母模groove punch 压线冲子
air-cushion eject-rod 气垫顶杆
spring-box eject-plate 弹簧箱顶板
bushing block 衬套insert 入块
club car 高尔夫球车
capability 能力parameter 参数
factor 系数phosphate 皮膜化成
viscosity 涂料粘度
alkalidipping 脱脂main manifold 主集流脉
bezel 斜视规blanking 穿落模
dejecting 顶固模demagnetization 去磁;消磁
high-speed transmission 高速传递
heat dissipation 热传rack 上料
degrease 脱脂rinse 水洗
alkaline etch 龄咬desmut 剥黑膜
D.I. rinse 纯水次Chromate 铬酸处理
Anodize 阳性处理seal 封孔
revision 版次part number/P/N 料号
good products 良品scraped products 报放心品
defective products 不良品finished products 成品
disposed products 处理品barcode 条码
flow chart 流程表单assembly 组装
stamping 冲压molding 成型
spare parts=buffer 备品coordinate 座标
dismantle the die 折模auxiliary fuction 辅助功能
poly-line 多义线heater band 加热片
thermocouple 热电偶sand blasting 喷沙
grit 砂砾derusting machine 除锈机
degate 打浇口dryer 烘干机
induction 感应induction light 感应光
response=reaction=interaction 感应
ram 连杆edge finder 巡边器
concave 凸convex 凹short 射料不足
nick 缺口speck 污点
shine 亮班splay 银纹gas mark 焦痕
delamination 起鳞cold slug 冷块
blush 导色gouge 沟槽;凿槽
satin texture 段面咬花witness line 证示线
patent 专利grit 沙砾granule=peuet=grain 细粒
grit maker 抽粒机
cushion 缓冲magnalium 镁铝合金
magnesium 镁金metal plate 钣金
lathe 车mill 锉plane 刨grind 磨
drill 钻boring 镗blinster 气泡
fillet 镶;嵌边through-hole form 通孔形式
voller pin formality 滚针形式
cam driver 铡楔shank 摸柄crank shaft 曲柄轴
augular offset 角度偏差velocity 速度
production tempo 生产进度现状
torque 扭矩spline=the multiple keys 花键
quenching 淬火tempering 回火annealing 退火
carbonization 碳化alloy 合金
tungsten high speed steel 钨高速的moly high speed steel 钼高速的
organic solvent 有机溶剂bracket 小磁导
liaison 联络单volatile 挥发性resistance 电阻
ion 离子titrator 滴定仪beacon 警示灯
coolant 冷却液crusher 破碎机
模具工程类
plain die 简易模pierce die 冲孔模
forming die 成型模progressive die 连续模
gang dies 复合模shearing die 剪边模
riveting die 铆合模pierce 冲孔
forming 成型(抽凸,冲凸)draw hole 抽孔
bending 折弯trim 切边
emboss 凸点dome 凸圆
semi-shearing 半剪
stamp mark 冲记号deburr or coin 压毛边
punch riveting 冲压铆合side stretch 侧冲压平
reel stretch 卷圆压平groove 压线
blanking 下料stamp letter 冲字(料号)
shearing 剪断tick-mark nearside 正面压印
tick-mark farside 反面压印
冲压名称类
extension dwg 展开图procedure dwg 工程图
die structure dwg 模具结构图material 材质
material thickness 料片厚度
factor 系数upward 向上downward 向下
press specification 冲床规格die height range 适用模高
die height 闭模高度burr 毛边gap 间隙weight 重量
total wt.总重量punch wt.上模重量
五金零件类
inner guiding post 内导柱inner hexagon screw 内六角螺钉
dowel pin 固定销coil spring 弹簧lifter pin 顶料销
eq-height sleeves=spool 等高套筒pin 销
lifter guide pin 浮升导料销guide pin 导正销
wire spring 圆线弹簧outer guiding post 外导柱
stop screw 止付螺丝located pin 定位销
outer bush 外导套 top plate 上托板(顶板)
top block 上垫脚punch set 上模座
punch pad 上垫板punch holder 上夹板
stripper pad 脱料背板up stripper 上脱料板
male die 公模(凸模)feature die 公母模
female die 母模(凹模)upper plate 上模板
lower plate 下模板die pad 下垫板
die holder 下夹板
die set 下模座bottom block 下垫脚
bottom plate 下托板(底板)stripping plate 内外打(脱料板)
outer stripper 外脱料板inner stripper 内脱料板
lower stripper 下脱料板
零件类
punch 冲头insert 入块(嵌入件)
deburring punch 压毛边冲子
groove punch 压线冲子
stamped punch 字模冲子
round punch 圆冲子
special shape punch 异形冲子
bending block 折刀
roller 滚轴
baffle plate 挡块
located block 定位块
supporting block for location
定位支承块
air cushion plate 气垫板
air-cushion eject-rod 气垫顶杆
trimming punch 切边冲子
stiffening rib punch = stinger 加强筋冲子
ribbon punch 压筋冲子
reel-stretch punch 卷圆压平冲子
guide plate 定位板
sliding block 滑块
sliding dowel block 滑块固定块
active plate 活动板
lower sliding plate 下滑块板
upper holder block 上压块
upper mid plate 上中间板
spring box 弹簧箱
spring-box eject-rod 弹簧箱顶杆
spring-box eject-plate 弹簧箱顶板
bushing bolck 衬套
cover plate 盖板
guide pad 导料块
塑件&模具相关英文
compre sion molding 压缩成型
flash mold 溢流式模具
plsitive mold 挤压式模具
split mold 分割式模具
cavity 型控 母模
core 模心 公模
taper 锥拔
leather cloak 仿皮革
shiver 饰纹
flow mark 流痕
welding mark 溶合痕
post screw insert 螺纹套筒埋值
self tapping screw 自攻螺丝
striper plate 脱料板
piston 活塞
cylinder 汽缸套
chip 细碎物
handle mold 手持式模具
移转成型用模具
encapsulation molding 低压封装成型
射出成型用模具
two plate 两极式(模具)
well type 蓄料井
insulated runner 绝缘浇道方式
hot runner 热浇道
runner plat 浇道模块
valve gate 阀门浇口
band heater 环带状的电热器
spindle 阀针
spear head 刨尖头
slag well 冷料井
cold slag 冷料渣
air vent 排气道
h=0.02~0.05mm w=3.2mm L=3~5mm
welding line 熔合痕
eject pin 顶出针
knock pin 顶出销
return pin 回位销反顶针
sleave 套筒
stripper plate 脱料板
insert core 放置入子
runner stripper plate 浇道脱料板
guide pin 导销
eject rod (bar)(成型机)顶业捧
subzero 深冷处理
three plate 三极式模具
runner system 浇道系统
stress crack 应力电裂
orientation 定向
sprue gate 射料浇口,直浇口
nozzle 射嘴
sprue lock pin 料头钩销(拉料杆)
slag well 冷料井
side gate 侧浇口
edge gate 侧缘浇口
tab gate 搭接浇口
film gate 薄膜浇口
flash gate 闸门浇口
slit gate 缝隙浇口
fan gate 扇形浇口
dish gate 因盘形浇口
H=F=1/2t~1/5t T=2.5~3.5mm
diaphragm gate 隔膜浇口
ring gate 环形浇口
subarine gate 潜入式浇口
tunnel gate 隧道式浇口
pin gate 针点浇口
Φ0.8~1.0mm
Runner less 无浇道
(sprue less)无射料管方式
long nozzle 延长喷嘴方式
sprue 浇口;溶渣
品质人员名称类
QC quality control 品质管理人员
FQC final quality control 终点品
质管制人员
IPQC in process quality control
制程中的品质管制人员
OQC output quality control 最终出货品质管制人员
IQC incoming quality control 进料品质管制人员
TQC total quality control 全面质量管理
POC passage quality control 段检人员
QA quality assurance 质量保证人员
OQA output quality assurance 出货质量保证人员
QE quality engineering 品质工程人员
品质保证类
FAI first article inspection 新品首件检查
FAA first article assurance 首件确认
TVR tool verification report 模具确认报告
3B 3B 模具正式投产前确认
CP capability index 能力指数
CPK capability index of process 模具制程能力参数
SSQA standardized supplier quality合格供应商品质评估
OOBA out of box audit 开箱检查
QFD quality function deployment品质机能展开
FMEA failure model effectiveness analysis 失效模式分析
8 disciplines 8 项回复内容
FA final audit 最后一次审核
CAR corrective action request 改正行动要求
corrective action report 改正行动报告
FQC 运作类
AQL Acceptable Quality Level 运作类允收品质水准
S/S Sample size 抽样检验样本大小
ACC Accept 允收
REE Reject 拒收
CR Critical 极严重的
MAJ Major 主要的
MIN Minor 轻微的
AOQ Average Output Quality 平均出厂品质
AOQL Average Output Quality Level 平均出厂品质
Q/R/S Quality/Reliability/Service品质/可靠度服务
MIL-STD Military-Standard 军用标准
S I-S IV Special I-Special IV 特殊抽样水准等级
P/N Part Number 料号
L/N Lot Number 特采
AOD Accept On Deviation 特采
UAI Use As It 首件检查报告
FPIR First Piece Inspection Report百万分之一
PPM Percent Per Million 批号制程统计品管专类
SPC Statistical Process Control 统计制程管制
SQC Statistical Quality Control 统计品质管制
R Range 全距
AR Averary Range 全距平均值
UCL Upper Central Limit 管制上限
LCL Lower Central Limit 管制下限
MAX Maximum 最大值
MIN Minimum 最小值
GRR Gauge
Reproducibility&Repeatability 量具之再制性及重测性判断量可靠与否
DIM Dimension 尺寸
DIA Diameter 直径
FREQ Frequency 频率
N Number 样品数
其它品质术语类
QCC Quality Control Circle 品质圈
QIT Quality Improvement Team 品质改善小组
PDCA Plan Do Check Action 计划执行 检查 总结
ZD Zero Defect 零缺点
QI Quality Improvement 品质改善
QP Quality Policy 目标方针
TQM Total Quality Management全面品质管理
MRB Material Reject Bill 退货单
LQL Limiting Quality Level 最低品质水准
RMA Return Material Audit 退料认可
QAN Quality Amelionrate Notice品质改善活动
ADM Absolute Dimension Measurement 全尺寸测量
QT Quality Target 品质目标
7QCTools 7 Quality Controll Tools品管七大手法
通用之件类
ECN Engineering Change Notes 工程变更通知(供应商)
ECO Engineering Change Order 工程改动要求(客户)
PCN Process Change Notice 工序改动通知
PMP Product Management Plan 生产管制计划
SIP Specification In Process 制程检验规格
SOP Standard Operation Procedure制造作业规范
IS Inspection Specification 成品检验规范
BOM Bill Of Material 物料清单
PS Package Specification 包装规范
SPEC Specification 规格
DWG Drawing 图面系统文件类
QC Quality System 品质系统
ES Engineering Standarization 工程标准
CGOO China General PCE 龙华厂文件
H Huston (美国)休斯敦
C Compaq (美国)康伯公司
C China 中国大陆
A Assembly 组装(厂)
S Stamping 冲压(厂)
P Painting 烤漆(厂)
I Intel 英特尔公司
T TAIWAN 台湾
IWS International Workman Standard 工艺标准
ISO International Standard Organization 国际标准化组织
GS General Specification 一般规格
CMCS C-China M-Manufacture C-Compaq S-Stamping Compaq 产
品在龙华冲压厂制造作业规范
CQCA Q-Quality A-Assembly
Compaq 产品在龙华组装厂品管作业规范
CQCP P-Painting Company 产品在龙华烤漆厂品管作业规范部类
PMC Production & Material Control 生产和物料控制
PPC Production Plan Control 生产计划控制
MC Material Control 物料控制
ME Manafacture Engineering 制造工程部
PE Project Engineering 产品工程部
A/C Accountant Dept 会计部
P/A Personal & Administration 人事行政部
DC Document Center 资料中心
QE Quality Engineering 品质工程(部)
QA Quality Assurance 品质保证(处)
QC Quality Control 品质管制(课)
PD Product Department 生产部
LAB Labratry 实验室
IE Industrial Engineering 工业工程
R&D Research & Design 设计开发部
P Painting 烤漆(厂)
A Asssembly 组装(厂)
S Stamping 冲压(厂)
生产类
PCS Pieces 个(根,块等)
PRS Pairs 双(对等)
CTN Carton 卡通箱
PAL Pallet/skid 栈板
PO Purchasing Order 采购订单
MO Manufacture Order 生产单
D/C Date Code 生产日期码
ID/C Identification Code (供应商)识别码
SWR Special Work Request 特殊工作需求
L/N Lot Number 批号
P/N Part Number 料号其它
OEM Original Equipment Manufacture 原设备制造
PCE Personal Computer Enclosure个人电脑外设
PC Personal Computer 个人电脑
CPU Central Processing Unit 中央处理器
SECC SECC` 电解片
SGCC SGCC 热浸镀锌材料
NHK North of Hongkong 中国大陆
PRC People's Republic of China
中国大陆
U.S.A the United States of America美国
A.S.A.P As Soon As Possible 尽可能快的
E-MAIL Electrical-Mail 电子邮件
N/A Not Applicable 不适用
QTY Quantity 数量
VS 以及
REV Revision 版本
JIT Just In Time 零库存
I/O Input/Output 输入/输出
OK Ok 好
NG Not Good 不行,不合格
C=0 Critical=0 极严重不允许
ESD Electry-static Discharge 静电排放
5S 希腊语 整理,整顿,清扫,清洁,教养
ATIN Attention 知会
CC Carbon Copy 副本复印相关人员
APP Approve 核准,认可,承认
CHK Check 确认
AM Ante Meridian 上午
PM Post Meridian 下午
CD Compact Disk 光碟
CD-ROM Compact Disk Read-Only
Memory 只读光碟
FDD Floppy Disk Drive 软碟机
HDD Hard Disk Drive 碟碟机
REF Reference 仅供参考
CONN Connector 连接器
CAV Cavity 模穴
CAD Computer Aid Design 计算机辅助设计
ASS'Y Assembly 装配,组装
MAT'S Material 材料
IC Integrated Circuit 集成电路
T/P True Position 真位度
TYP Type 类型
WDR Weekly Delivery Requitement周出货需求
C?T Cycle Time 制程周期
L/T Lead Time 前置时间(生产前准备时间)
S/T Standard Time 标准时间
P/M Product Market 产品市场
3C Computer,Commumcation,Consumer electronic 消费性电子
5WIH
When,Where,Who,What,Why,How to
5M
Man,Machine,Material,Method,Measur
ement
4MIH
Man,Materia,Money,Method,Time
人力,物力,财务,技术,时间(资源)
SQA Strategy Quality Assurance
策略品质保证
DQA Desigh Quality Assurance 设计品质保证
MQA Manufacture Quality Assurance 制造品质保证
SSQA Sales and service Quality Assurance 销售及服务品质保证
LRR Lot Rejeet Rate 批退率
BS Brain storming 脑力激荡
EMI Electronic Magnetion Inspect高磁测试
FMI Frequency Modulatim Inspect高频测试
B/M Boar/Molding(flat cable)
C/P Connector of PC
A/P Assembly
SPS Switching power supply 电源箱
DT Desk Top 卧式(机箱)
MT Mini-Tower 立式(机箱)
DVD Digital Vedio Disk
VCD Vdeio Compact Disk
LCD Liquid Crystal Display
CAD Computer AID Design
CAM Computer AID Manufacturing
CAE Computer AID Engineering
ABIOS Achanced Basic in
put/output system 先进的基本输入/输出系统
CMOS Complemeruary Metoll
Oxide Semiconductor 互补金属氧化物半导体
PDA Personal Digital Assistant 个人数字助理
IC Integrated Circuit 集成电路
ISA Industry Standard Architecture工业标准体制结构
MCA Micro Channel Architecture微通道结构
EISA Extended Industry Standard Architecture 扩充的工业标准结构
SIMM Single in-line memory module 单项导通汇流组件
DIMM Dual in-line Memory Module
双项导通汇流组件
LED Light-Emitting Diode 发光二级管
FMEA Failure Mode Effectivenes失效模式分析
W/H Wire Harness 金属线绪束集组件
F/C Flat Calle 排线
PCB Printed Circuit Board 印刷电路板
CAR Correction Action Report 改善报告
NG Not Good 不良
WPR Weekly Delivery Requirement周出货要求
PPM Parts Per Million 百万分之一
TPM Total Production Maintenance全面生产保养
MRP Material Requiremcnt Planning物料需计划
OC Operation System 作业系统
TBA To Be Design 待定,定缺
D/C Drawing Change
P/P Plans & Procedune
EMI Electrical-Music Industry 电子音乐工业
RFI Read Frequency Input 读频输入
MMC Maximum Material Condition
MMS Maximum Material Size
LMC Least Material Condition
LMS Least Material Size
模具技术用语
各种模具常用成形方式
accurate die casting 精密压铸
powder forming 粉末成形
calendaring molding 压延成形
powder metal forging 粉末锻造
cold chamber die casting 冷式压铸
precision forging 精密锻造
cold forging 冷锻 press forging 冲锻
compacting molding 粉末压出成形
rocking die forging 摇动锻造
compound molding 复合成形 rotary
forging 回转锻造
compression molding 压缩成形
rotational molding 离心成形
dip mold 浸渍成形
rubber molding橡胶成形
encapsulation molding 注入成形
sand mold casting 砂模铸造
extrusion molding 挤出成形 shell
casting 壳模铸造
foam forming 泡成形
sinter forging烧结锻造
forging roll 轧锻 six sides forging 六面锻造
gravity casting 重力铸造
Slush molding 凝塑成形
hollow(blow) molding 中空(吹出)成形
squeeze casting 高压铸造
hot chamber die casting 热室压铸
swaging 挤锻
hot forging 热锻
transfer molding 转送成形
injection molding 射出成形
Warm forging 温锻
investment casting 精密铸造
matched die method 对模成形法
laminating method 被覆淋膜成形
low pressure casting 低压铸造
lost wax casting 脱蜡铸造 matched
mould thermal forming 对模热成形模
各式模具分类用语
bismuth mold 铋铸模 landed plunger
mold 有肩柱塞式模具
burnishing die 挤光模 landed positive
mold 有肩全压式模具
button die 镶入式圆形凹模 loading
shoe mold 料套式模具
center-gated mold 中心浇口式模具
loose detail mold 活零件模具
chill mold 冷硬用铸模 loose mold
活动式模具
clod hobbing 冷挤压制模 louvering
die 百叶窗冲切模
composite dies 复合模具 manifold
die 分歧管模具
counter punch 反凸模 modular mold
组合式模具
double stack mold 双层模具
multi-cavity mold 多模穴模具
electroformed mold 电铸成形模
multi-gate mold 复式浇口模具
expander die 扩径模 offswt bending
die 双折冷弯模具
extrusion die 挤出模
palletizing die叠层模
family mold 反套制品模具 plaster
mold 石膏模
blank through dies 漏件式落料模
porous mold 通气性模具
duplicated cavity plate 复板模
positive mold 全压式模具
fantail die 扇尾形模具 pressure die压紧模
fishtail die 鱼尾形模具
profile die轮廓模
flash mold 溢料式模具
Progressive die 顺序模
gypsum mold 石膏铸模
Portable mold 手提式模具
hot-runner mold 热流道模具
prototype mold 雏形试验模具
ingot mold 钢锭模
punching die 落料模
lancing die 切口模
raising(embossing)压花起伏成形
re-entrant mold 倒角式模具
Sectional die 拼合模
runless injection mold 无流道冷料模具
sectional die 对合模具
segment mold 组合模 semi-positive
mold 半全压式模具
shaper 定型模套
single cavity mold单腔模具
solid forging die 整体锻模
Split forging die 拼合锻模
split mold 双并式模具
Spineless mold 无注道残料模具
squeezing die 挤压模
stretch form die拉伸成形模
sweeping mold 平刮铸模
swing die振动模具
three plates mold 三片式模具
trimming die 切边模
unit mold 单元式模具
universal mold通用模具
unscrewing mold 退扣式模具 yoke
type die 轭型模
模具厂常用之标准零配件
air vent vale 通气阀
anchor pin 锚梢
angular pin 角梢
baffle 调节阻板
angular pin 倾斜梢
baffle plate 折流档板
ball button 球塞套
ball plunger 定位球塞
ball slider 球塞滑块
binder plate 压板
blank holder 防皱压板
blanking die落料冲头
bolster 上下模板
bottom board 浇注底板
bolster 垫板
bottom plate 下固定板
bracket 托架
bumper block 缓冲块
buster 堵口
casting ladle 浇注包
casting lug 铸耳
cavity 模穴(模仁)
cavity retainer plate
模穴托板 center
pin 中心梢
clamping block 锁定块
coil spring螺旋弹簧
cold punched nut 冷冲螺母
Cooling spiral 螺旋冷却栓
core 心型
core pin 心型梢
cotter 开口梢
cross 十字接头
cushion pin 缓冲梢
diaphragm gate盘形浇口
die approach 模头料道
die bed 型底
die block 块形模体
die body 铸模座
die bush 合模衬套
die button 冲模母模
die clamper 夹模器
die fastener 模具
固定用零件
die holder 母模固定板
die lip 模唇
die plate 冲模板
die set 冲压模座
direct gate 直接浇口
dog chuck 爪牙,夹头
dowel 定位梢
dowel hole 导套孔
dowel pin 合模梢
dozzle 辅助浇口
dowel pin 定位梢
draft 拔模锥度
draw bead 张力调整杆
drive bearing传动轴承
ejection pad 顶出衬垫
ejector 脱模器
ejector guide pin 顶出导梢
Ejector leader busher 顶出导梢衬套
ejector pad 顶出垫
ejector pin 顶出梢
ejector plate 顶出板
ejector rod 顶出杆
ejector sleeve 顶出衬套 ejector valve顶出阀
eye bolt 环首螺栓
filling core 椿入蕊
film gate 薄膜形浇口
finger pin 指形梢
finish machined plate 角形模板
finish machined round plate 圆形模板
fixed bolster plate 固定侧模板
flanged pin 带凸缘?
flash gate 毛边形浇口 flask 上箱
floating punch 浮动冲头 gate 浇口
gate land 浇口面
gib 凹形拉紧
goose neck 鹅颈管 guide bushing 引导衬套
guide pin 导梢 guide post 引导柱
guide plate 导板 guide rail 导轨
head punch 顶部冲头
headless punch直柄冲头
heavily tapered solid 整体模蕊盒
hose nippler 管接头
impact damper 缓冲器
injection ram压射柱塞
inlay busher 嵌入衬套
inner plunger内柱塞
inner punch 内冲头
insert 嵌件
insert pin 嵌件梢
king pin 转向梢
king pin bush 主梢衬套
knockout bar脱模杵
land 合模平坦面
land area 合模面
leader busher 导梢衬套
lifting pin 起模顶
lining 内衬
locating center punch 定位中心冲头
locating pilot pin 定位导梢
Locating ring 定位环
lock block 压块
locking block 定位块
locking plate 定位板
loose bush 活动衬套
making die 打印冲子
manifold block 歧管档块
master plate 靠模样板
match plate分型板
mold base 塑胶模
mold clamp 铸模紧固夹
mold platen 模用板
moving bolster换模保持装置
moving bolster plate 可动侧模板
One piece casting 整体铸件
parallel block 平行垫块
paring line分模线
parting lock set 合模定位器
Pass guide 穴型导板
peened head punch 镶入式冲头
pilot pin 导?
pin gate 针尖浇口
plate 衬板
pre extrusion punch 顶挤冲头
punch冲头
puncher 推杆
pusher pin 衬套梢
rack 机架
rapping rod 起模杆
re-entrant mold 凹入模
retainer pin嵌件梢
retainer plate 托料板
return pin 回位梢
riding stripper 浮动脱模器
ring gate环型浇口
roller 滚筒
runner 流道
runner ejector set
流道顶出器
Runner lock pin 流道拉梢
screw plug 头塞
set screw 固定螺丝
shedder 脱模装置
shim 分隔片
shoe 模座之上下模板
shoot 流道
shoulder bolt肩部螺丝
skeleton 骨架
slag riser 冒渣口
slide(slide core) 滑块
slip joint 滑配接头
spacer block 间隔块
spacer ring 间隔环
spider 模蕊支架
spindle 主轴
sprue 注道
sprue bushing 注道衬套
Sprue bushing guide 注道导套
sprue lock bushing 注道定位衬套
sprue puller 注道拉料?
spue line 合模线 square key 方键
square nut 方螺帽 square thread 方螺纹
stop collar 限位套 stop pin 止动梢
stop ring 止动环 stopper 定位停止梢
straight pin 圆柱? stripper bolt 脱料螺栓
stripper bushing 脱模衬套 stripper plate 剥料板
stroke end block 行程止梢 submarine gate 潜入式浇口
support pillar 支撑支柱/ 顶出支柱
support pin 支撑梢
supporting plate 托板 sweep templete造模刮板
tab gate 辅助浇口 taper key 推拔键
taper pin 拔锥梢/锥形梢 teeming 浇注
three start screw 三条螺纹 thrust pin推力销
tie bar 拉杵 tunnel gate 隧道形浇口
vent 通气孔 wortle plate 拉丝模板
模具常用之工作机械
3D coordinate measurement 三次元量
床 boring machine 搪孔机
cnc milling machine CNC 铣床
contouring machine 轮廓锯床
copy grinding machine 仿形磨床
copy lathe 仿形车床
copy milling machine 仿形铣床 copy
shaping machine 仿形刨床
cylindrical grinding machine 外圆磨
床 die spotting machine 合模机
drilling machine ? 孔机 engraving
machine 雕刻机
engraving E.D.M. 雕模放置加工机
form grinding machine 成形磨床
graphite machine 石墨加工机
horizontal boring machine 卧式搪孔机
horizontal machine center 卧式加工
制造中心 internal cylindrical machine内圆磨床
jig boring machine 冶具搪孔机 jig grinding machine 冶具磨床
lap machine 研磨机 machine center加工制造中心
multi model miller 靠磨铣床 NC
drilling machine NC 钻床
NC grinding machine NC 磨床 NC
lathe NC 车床
NC programming system NC 程式制
作系统 planer 龙门刨床
profile grinding machine 投影磨床
projection grinder 投影磨床
radial drilling machine 旋臂? 床
shaper 牛头刨床
surface grinder 平面磨床 try machine试模机
turret lathe 转塔车床 universal tool
grinding machine 万能工具磨床
vertical machine center 立式加工制造
中心 wire E.D.M. 线割放电加工机
检验量测工具用语
autocollimator 自动准直机 benchcomparator 比长仪
block gauge 块规 bore check 精密小测定器
calibration 校准 caliper gauge 卡规
check gauge 校对规 clearance gauge间隙规
clinoretee 测斜仪 comparator 比测仪
cylinder square 圆筒直尺 depth gauge 测深规
dial indicator 针盘指示表 dial snap gauge 卡规
digital micrometer 数位式测微计
feeler gauge 测隙规
gauge plate 量规定位板 height gauge测高规
inside calipers 内卡钳 inside
micrometer 内分??卡
interferometer 干涉仪 leveling block平台
limit gauge 限规 micrometer 测微计
mil 千分之一寸 monometer 压力计
morse taper gauge 莫氏锥度量规
nonius 游标卡尺
optical flat 光学平晶 optical parallel光学平行
passimeter 内径仪 position scale 位置刻度
profile projector 轮廓光学投影仪
protractor 分角器
radius 半径 ring gauge 环规
sine bar 正弦量规 snap gauge 卡模
square master 直角尺 stylus 触针
telescopic gauge 伸缩性量规
working gauge 工作量规
模具钢材
alloy tool steel 合金工具钢
aluminium alloy 铝合金钢
bearing alloy 轴承合金 blister steel
浸碳钢
bonderized steel sheet 邦德防蚀钢板
carbon tool steel 碳素工具钢
clad sheet 被覆板 clod work die steel
冷锻模用钢
emery 金钢砂 ferrostatic pressure 钢
铁水静压力
forging die steel 锻造模用钢
galvanized steel sheet 镀锌铁板
hard alloy steel 超硬合金钢 high
speed tool steel 高速度工具钢
hot work die steel 热锻模用钢 lowalloy tool steel 特殊工具钢
low manganese casting steel 低锰铸钢 marging steel 马式体高强度热处理钢
martrix alloy 马特里斯合金
meehanite cast iron 米汉纳铸钢
meehanite metal 米汉纳铁 merchant iron 市售钢材
molybdenum high speed steel 钼系高速钢 molybdenum steel 钼钢
nickel chromium steel 镍铬钢
prehardened steel 顶硬钢
silicon steel sheet 矽钢板 stainless steel 不锈钢
tin plated steel sheet 镀锡铁板 tough pitch copper 韧铜
troostite 吐粒散铁 tungsten steel ?钢
vinyl tapped steel sheet 塑胶覆面钢板
表面处理关连用语
age hardening 时效硬化 ageing 老化处理
air hardening 气体硬化 air patenting
空气韧化
annealing 退火 anode effect 阳极效应
anodizing 阳极氧化处理 atomloytreatment 阿托木洛伊表面
austempering 奥氏体等温淬火austenite 奥斯田体/奥氏体
bainite 贝氏体 banded structure 条纹状组织
barrel plating 滚镀 barrel tumbling滚筒打光
blackening 染黑法 blue shortness 青熟脆性
bonderizing 磷酸盐皮膜处理 box
annealing 箱型退火
box carburizing 封箱渗碳 bright
electroplating 辉面电镀
bright heat treatment 光辉热处理
bypass heat treatment 旁路热处理
carbide 炭化物 carburized case depth
浸碳硬化深层
carburizing 渗碳 cementite 炭化铁
chemical plating 化学电镀 chemical
vapor deposition 化学蒸镀coarsening 结晶粒粗大化 coating 涂
布被覆
cold shortness 低温脆性 comemtite
渗碳体
controlled atmosphere 大气热处理
corner effect 锐角效应
creeping discharge 蠕缓放电
decarburization 脱碳处理
decarburizing 脱碳退火 depth of
hardening 硬化深层
diffusion 扩散 diffusion annealing 扩
散退火
electrolytic hardening 电解淬火
embossing 压花
etching 表面蚀刻 ferrite 肥粒铁
first stage annealing 第一段退火
flame hardening 火焰硬化
flame treatment 火焰处理 full
annealing 完全退火
gaseous cyaniding 气体氧化法
globular cementite 球状炭化铁
grain size 结晶粒度 granolite
treatment 磷酸溶液热处理
graphitizing 石墨退火 hardenability
硬化性
hardenability curve 硬化性曲线
hardening 硬化
heat treatment 热处理 hot bath
quenching 热浴淬火
hot dipping 热浸镀 induction
hardening 高周波硬化
ion carbonitriding 离子渗碳氮化 ion
carburizing 离子渗碳处理
ion plating 离子电镀 isothermal
annealing 等温退火
liquid honing 液体喷砂法 low
temperature annealing 低温退火
malleablizing 可锻化退火
martempering 麻回火处理
martensite 马氏体/ 硬化铁炭
metallikon 金属喷镀法
metallizing 真空涂膜 nitriding 氮化
处理
nitrocarburizing 软氮化 normalizing
正常化
oil quenching 油淬化 overageing 过老化
overheating 过热 pearlite 针尖组织
phosphating 磷酸盐皮膜处理
physical vapor deposition 物理蒸镀
plasma nitriding 离子氮化
pre-annealing 预备退火
precipitation 析出 precipitation
hardening 析出硬化
press quenching 加压硬化 process
annealing 制程退火
quench ageing 淬火老化 quench
hardening 淬火
quenching crack 淬火裂痕 quenching
distortion 淬火变形
quenching stress 淬火应力
reconditioning 再调质
recrystallization 再结晶 red shortness红热脆性
residual stress 残留应力 retained austenite 残留奥
rust prevention 防蚀 salt bath
quenching 盐浴淬火
sand blast 喷砂处理 seasoning 时效处理
second stage annealing 第二段退火
secular distortion 经年变形
segregation 偏析 selective hardening部分淬火
shot blast 喷丸处理 shot peening 珠击法
single stage nitriding 等温渗氮
sintering 烧结处理
soaking 均热处理 softening 软化退火
solution treatment 固溶化热处理
spheroidizing 球状化退火
stabilizing treatment 安定化处理
straightening annealing 矫直退火
strain ageing 应变老化 stress
relieving annealing 应力消除退火
subzero treatment 生冷处理
supercooling 过冷
surface hardening 表面硬化处理
temper brittleness 回火脆性
temper colour 回火颜色 tempering回火
tempering crack 回火裂痕 texture 咬花
thermal refining 调质处理
thermoechanical treatment 加工热处理
time quenching 时间淬火
transformation 变态
tufftride process 软氮化处理 under
annealing 不完全退火
vacuum carbonitriding 真空渗碳氮化
vacuum carburizing 真空渗碳处理
vacuum hardening 真空淬火 vacuum
heat treatment 真空热处理
vacuum nitriding 真空氮化 water
quenching 水淬火
wetout 浸润处理
焊接用语
acetylene 乙炔 ampere 电流安培
angle welding 角焊 arc 电弧
argon arc welding 氩弧焊接 bare
electrode 光熔接条
butt welding 对接焊接 camber 电弧弯曲
cascade 阶叠熔接法 clad weld 被覆熔接
crator 焊疤 excess metal 多余金属
filler rod 焊条 fillet weld 填角焊接
gas shield 气体遮蔽 groove welding起槽熔接
hand face shield 手握面罩 hard
facing 硬表面堆焊
jig welding 工模焊接 laser beam
welding 雷射光焊接
metal electrode insert gas welding
MIG 熔接 nugget 点焊熔核
overlaying 堆焊 peening of welding珠击熔接法
plug welding 塞孔熔接 positioned welding 正向熔接
pressure welding 压焊 propane gas
cutting 丙烷气切割pure nickel electrode 纯镍熔接条
reinforcement of weld 加强焊接resist 抗蚀护膜 root running 背面熔接
seam 焊缝 seaming 接合
seam welding 流缝熔接 series seam
welding 串联缝熔接
skip welding process 跳焊法 spark火花
spot welding 点焊接 stitch welding针角焊接
stud arc welding 电弧焊接 under
laying 下部焊层
void 焊接空隙 weld flow mark 焊接
流痕
weld flush 焊缝凸起 weld line 焊接纹
weld mark 焊接痕 weld penetration熔接透入
weld zone 焊接区 welding 焊接
welding bead 焊接泡 welding
direction 焊接方向
welding distortion 焊接变形 welding flux 焊剂
welding ground 电熔接地 welding
interval 焊接周期
welding stress 熔接应变 welding torch 熔接气炬
射出成形关联用语
activator 活化剂 bag moulding 气胎施压成形
bonding strength 黏合强度 breathing排气
caulking compound 填隙料 cell 气孔
cold slug 半凝式射出 colorant 著色剂
color matching 调色 color
masterbatch 色母料
compound 混合料 copolymer 共聚合体
cull 残料废品 cure 凝固化
cryptometer 不透明度仪 daylight 开隙
dry cycle time 空料试车周期时间
ductility 延性
elastomer 弹性体 extruded bead
sealing 压出粒涂层法
feed 供料 filler 充填剂
film blowing 薄膜吹制法 floating
platen 活动模板
foaming agent 发泡剂 gloss 光泽
granule 颗粒料 gunk 料斗
hot mark 热斑 hot stamping 烫印
injection nozzle 射出喷嘴 injection
plunger 射出柱塞
injection ram 射出冲柱 isomer 同分异构物
kneader 混合机 leveling agent 匀涂剂
lubricant 润滑剂 matched die method配合成形法
mould clamping force 锁模力 mould release agent 脱模剂
nozzle 喷嘴 oriented film 取向薄膜
parison 吹气成形坏料 pellet 粒料
plasticizer 可塑剂 plunger 压料柱塞
porosity 孔隙率 post cure 後固化
premix 预混料 purging 清除
reciprocating screw 往复螺杆
resilience 回弹性
resin injection 树脂射出法 rheology流变学
sheet 塑胶片 shot 注射
shot cycle 射出循环 slip agent 光滑剂
take out device 取料装置 tie bar 拉杆
toggle type mould clamping system 杆式锁模装置
torpedo spreader 鱼雷形分流板
transparency 透明性
void content 空洞率
塑胶原料
acrylic 压克力 casein 酪素
cellulose acetate 醋酸纤维素CA
cellulose acetate butyrate 醋酸丁酸纤
维素CAB
composite material 复合材料 cresol
resin 甲酚树脂CF
dially phthalate 苯二甲酸二烯丙酯
disperse reinforcement 分散性强化复合材料
engineering plastics 工程塑胶 epoxy
resin 环氧树脂EP
ethyl cellulose 乙基纤维素 ethylene
vinylacetate copolymer 乙烯-醋酸乙烯EVA
ethylene-vinlacetate copolyme 醋酸乙
烯共聚物EVA expanded polystyrene泡聚苯乙烯EPS
fiber reinforcement 纤维强化热固性/纤维强化复合材料
high density polyethylene 高密度聚乙烯HDPE
high impact polystyrene 高冲击聚苯乙烯HIPS
high impact polystyrene rigidity 高冲击性聚苯乙烯
low density polyethylene 低密度聚乙
烯LDPE melamine resin 三聚氰胺酚醛树脂MF
nitrocellulose 硝酸纤维素 phenolic
resin 酚醛树脂
plastic 塑胶 polyacrylic acid 聚丙烯酸PAP
polyamide 耐龙PA
polybutyleneterephthalate 聚对苯二甲酸丁酯PBTpolycarbonate 聚碳酸酯PC
polyethyleneglycol 聚乙二醇PFG
polyethyleneoxide 聚氧化乙烯PEO
polyethyleneterephthalate 聚乙醇对苯PETP
polymetylmethacrylate 聚甲基丙烯酸
甲酯PMMA polyoxymethylene 聚缩
醛POM
polyphenylene oxide 聚硫化亚苯
polyphenyleneoxide 聚苯醚PPO
polypropylene 聚丙烯PP polystyrene
聚苯乙烯PS
polytetrafluoroethylene 聚四氟乙烯
PTFE polytetrafluoroethylene 聚四氟
乙烯
polythene 聚乙烯PE polyurethane 聚
氨基甲酸酯PU
polyvinylacetate 聚醋酸乙烯PVAC
polyvinylalcohol 聚乙烯醇PVA
polyvinylbutyral 聚乙烯醇缩丁醛
PVB polyvinylchloride 聚氯乙烯
PVC
polyvinylfuoride 聚氟乙烯PVF
polyvinylidenechloride 聚偏二氯乙烯
PVDC
prepolymer 预聚物 silicone resin 矽
树脂
thermoplastic 热塑性 thermosetting
热固性
thermosetting plastic 塑胶
unsaturated polyester 不饱和聚酯树脂
成形不良用语
aberration 色差 atomization ?化
bank mark ?料纹 bite 咬入
blacking hole 涂料孔(铸疵) blacking
scab 涂料疤
blister 起泡 blooming 起霜
blow hole 破孔 blushing 泛白
body wrinkle 侧壁皱纹 breaking-in冒口带肉
bubble 膜泡 burn mark 糊斑
burr 毛边 camber 翘曲
cell 气泡 center buckle 表面中部波皱
check 细裂痕 checking 龟裂
chipping 修整表面缺陷 clamp-off
铸件凹痕
collapse 塌陷 color mottle 色斑
corrosion 腐蚀 crack 裂痕
crazing 碎裂 crazing 龟裂
deformation 变形 edge 切边碎片
edge crack 裂边 fading 退色
filler speak 填充料斑 fissure 裂纹
flange wrinkle 凸缘起皱 flaw 刮伤
flow mark 流痕 galling 毛边
glazing 光滑 gloss 光泽
grease pits 污斑 grinding defect 磨痕
haircrack 发裂 haze 雾度
incrustation 水锈 indentation 压痕
internal porosity 内部气孔 mismatch
偏模
mottle 斑点 necking 缩颈
nick 割痕 orange peel 橘皮状表面
缺陷
overflow 溢流 peeling 剥离
pit 坑 pitting corrosion 点状腐蚀
plate mark 模板印痕 pock 麻点
pock mark 痘斑 resin streak 树脂流
纹
resin wear 树脂脱落 riding 凹陷
sagging 松垂 saponification 皂化
scar 疤痕 scrap 废料
scrap jam 废料阻塞 scratch 刮伤/划
痕
scuffing 深冲表面划伤 seam 裂痕
shock line 模口挤痕 short shot 充填
不足
shrinkage pool 凹孔 sink mark 凹痕
skin inclusion 表皮摺叠 straightening矫直
streak 条状痕 surface check 表面裂痕
surface roughening 橘皮状表皮皱摺
surging 波动
sweat out 冒汗 torsion 扭曲
warpage 翘曲 waviness 波痕
webbing 熔塌 weld mark 焊痕
whitening 白化 wrinkle 皱纹
模具常用刀具与工作法用语
adjustable spanner 活动扳手 angle
cutter 角铣刀
anvil 铁? arbour 心轴
backing 衬垫 belt sander 带式打磨
机
buffing 抛光 chamfering machine 倒
角机
chamfering tool 去角刀具 chisel 扁
錾
chuck 夹具 compass 两角规
concave cutter 凹面铣刀 convex
cutter 凸形铣刀
cross joint 十字接头 cutting edge
clearance 刃口余隙角
drill stand 钻台 edge file 刃用锉刀
file 锉刀 flange joint 凸缘接头
grinder 砂轮机 hammer 铁锤
hand brace 手摇钻 hatching 剖面线
hexagon headed bolt 六角头螺栓
hexagon nut 六角螺帽
index head 分度头 jack 千斤顶
jig 治具 kit 工具箱
lapping 研磨 metal saw 金工锯
nose angle 刀角 pinchers 钳子
pliers 铗钳 plug 柱塞头
polisher 磨光器 protable driller 手提
钻孔机
punch 冲头 sand paper 砂纸
scraper 刮刀 screw driver 螺丝起子
scribing 划线 second out file 中纹锉
spanner 扳手 spline broach 方栓槽
拉刀
square 直角尺 square sleeker 方形镘
刀
square trowel 直角度 stripping 剥离
工具
T-slot T 形槽 tool for lathe 车刀
tool point angle 刀刃角 tool post 刀
架
tosecan 划线盘 trimming 去毛边
waffle die flattening 压纹效平 wiper
脱模钳
wrench 螺旋扳手
电脑关联用语
3D modeling 三次元模拟 access 通
路
animation 卡通影片 application 应
用
board 基板 bug 故障
bus 汇流排 CAD 电脑辅助设计
CAE 电脑辅助工程分析 CAM 电脑辅助制造
cassette 卡座 color display 彩色显示器
command 指令 communication 通信
compact 精简小型 computer 电脑
copy 复制 cursor 游标
curve modeling 曲面模拟 database资料库
design 设计 digitizing 数位化
disk 磁碟 dot 点
eyelet 眼孔 floppy 磁碟片
format 格式化 graphic 圆解
hardware 硬体 honeycomb 蜂巢
interface 界面 know how 秘诀
laser printer 雷射印表机 lay out 布置
memory 记忆 memory swap 交换记忆
microprocessor 微处理器 modeling造型
module 模组 monitor 萤幕
mouse 滑鼠 need 需求
network 网路 new version 新版
on line 上线中 option 选择
PC 个人电脑 plotter 绘图机
program 程式 scanning 扫描
simulation 模拟 software 软体
solid model 实体模型 system 系统
tape 磁带 terminal 终端机
texture 构造 trim 修边
venter 排气风扇 word processor 文书处理器
各种冲模加工关连用语
barreling 滚光加工 belling 压凸加工
bending 弯曲加工 blanking 下料加工
bulging 撑压加工 burring 冲缘加工
cam die bending 凸轮弯曲加工
caulking ?合加工
coining 压印加工 compressing 压缩
加工
compression bending 押弯曲加工
crowning 凸面加工
curl bending 卷边弯曲加工 curling
卷曲加工
cutting 切削加工 dinking 切断蕊骨
double shearing 叠板裁断 drawing引伸加工
drawing with ironing 抽引光滑加工
embossing 浮花压制加工
extrusion 挤制加工 filing 锉削加工
fine blanking 精密下料加工 finish
blanking 光制下料加工
finishing 精整加工 flanging 凸缘加工
folding 折边弯曲加工 folding 摺叠加工
forming 成形加工 impact extrusion冲击挤压加工
indenting 压痕加工 ironing 引缩加工
knurling 滚花 lock seaming 固定接合
louvering 百叶窗板加工 marking 刻印加工
necking 颈缩加工 notching 冲口加工
parting 分断加工 piercing 冲孔加工
progressive bending 连续弯曲加工
progressive blanking 连续下料加工
progressive drawing 连续引伸加工
progressive forming 连续成形加工
reaming 铰孔加工 restriking 二次精冲加工
riveting ?接加工 roll bending 滚筒弯曲加工
roll finishing 滚压加工 rolling 压延加工
roughing 粗加工 scrapless machining无废料加工
seaming 折弯重叠加工 shaving 缺口修整加工
shearing 切断加工 sizing 精压加工/矫正加工
slitting 割缝加工 spinning 卷边?接
staking ?固 stamping 锻压加工
swaging 挤锻压加工 trimming 整缘加工
upsetting 锻粗加工 wiring 抽线加工
冲压机械及周边关连用语
back shaft 支撑轴 blank
determination 胚料展开
bottom slide press 下传动式压力机
board drop hammer 板落锤
brake 煞车 buckle 剥砂面
camlachie cramp 铸包 casting on flat ?合
chamotte sand 烧磨砂 charging
hopper 加料漏斗
clearance 间隙 closed-die forging 合模锻造
clump 夹紧 clutch 离合器
clutch brake 离合器制动器 clutch boss 离合器轮壳
clutch lining 离合器覆盖 coil car 带卷升降运输机
coil cradle 卷材进料装置 coil reel
stand 钢材卷料架
column 圆柱 connection screw 连杆调节螺钉
core compound 砂心黏结剂 counter blow hammer 对击锻锤
cradle 送料架 crank 曲柄轴
crankless 无曲柄式 cross crank 横向曲轴
cushion 缓冲 depression 外缩凹孔dial feed 分度送料
die approach 模口角度
die assembly 合模 die cushion 模具缓冲垫
die height 冲压闭合高度 die life 模具寿命
die opening 母模逃孔 die spotting press 调整冲模用压力机
double crank press 双曲柄轴冲床
draght angle 逃料倾斜角
edging 边锻伸 embedded core 加装砂心
feed length 送料长度 feed level 送料高度
filling core 埋入砂心 filling in 填砂
film play 液面花纹 fine blanking press 精密下料冲床
forging roll 辊锻机 finishing slag 炼后熔渣
fly wheel 飞轮 fly wheel brake 飞轮制动器
foot press 脚踏冲床 formboard 进模口板
gripper 夹具 gripper feed 夹持进料
gripper feeder 夹紧传送装置hammer 槌机
hand press 手动冲床 hand rack pinion press 手动齿轮齿条式冲床
hand screw press 手动螺旋式冲床
hopper feed 料斗送料
idle stage 空站 inching 微调尺寸
isothermal forging 恒温锻造 key clutch 键槽离合器
knockout 脱模装置 knuckle mechanic 转向机构
land 模具直线刀面部 level 水平
loader 供料器 unloader 卸料机
loop controller 闭回路控制器 lower die 下模
micro inching device 微寸动装置
microinching equipment 微动装置
motor 马达 moving bolster 活动工作台
notching press 冲缺口压力机
opening 排料逃孔
overload protection device 防超载装置
pinch roll 导正滚轮
pinion 小齿轮 pitch 节距
pressfit 压入 progressive 连续送料
pusher feed 推杆式送料 pusher
feeder 料片押片装置
quick die change system 快速换模系
统 regrinding 再次研磨
releasing 松释动作 reversed blanking反转下料
robot 机器人 roll forming machine辊轧成形
roll forming machine 辊轧成形机
roll release 脱辊
roller feed 辊式送料 roller leveler 辊式矫直机
rotary bender 卷弯成形机 safety
guard 安全保护装置
scrap cutter 废料切刀 scrap press 废料冲床
seamless forging 无缝锻造 separate分离
shave 崩砂 shear angle 剪角
sheet loader 薄板装料机 shot 单行程工作
shrinkage fit 收缩配合 shut height闭合高度
sieve mesh 筛孔 sintering of sand 铸砂烧贴
slide balancer 滑动平衡器 slug hole逃料孔
spin forming machine 旋压成形机spotting 合模
stack feeder 堆叠拨送料机 stickness黏模性
straight side frame 冲床侧板
stretcher leveler 拉伸矫直机
strip feeder 料材送料装置 stripping
pressure 弹出压力
stroke 冲程 take out device 取料装置
toggle press 肘杆式压力机 transfer传送
transfer feed 连续自动送料装置
turrent punch press 转塔冲床
two speed clutch 双速离合器
uncoiler 闭卷送料机
unloader 卸载机 vibration feeder 振动送料机
wiring press 嵌线卷边机
线切割放电加工关连用语
abnormal glow 不规则辉光放电 arc
discharge 电弧放电
belt 皮带 centreless 无心
chrome bronze 铭铜 clearance angle后角
corner shear drop 直角压陷
deflection 桡曲度
discharge energy 放电能量 dressing修整
dwell 保压 flange 凸缘
gap 间隙 graphite 石墨
graphite contraction allowance 电极缩小余量
graphite holder 电极夹座
hair crack 发裂 horn 电极臂
jump 跳刀 magnetic base 磁性座
master graphite 标准电极 pipe
graphite 管状电极
pulse 脉冲 rib working 肋部加工
roller electrode 滚轮式电极 rotary
surface 旋转面
shank 柄部 sharp edge 锐角部
tough bronze 韧铜 traverse 摇臂
tungsten bronze ?青铜 waviness 波形起伏
work 工件 working allowance 加工余量
working dischard 加工废料
锻铸造关连用语
accretion 炉瘤 acid converter 酸性转炉
acid lining cupola 酸性熔铁炉 acid open-hearth furnace 酸性平炉
aerator 松砂机 air set mold 常温自硬铸模
airless blasting cleaning 离心喷光 all core molding 集合式铸模
all round die holder 通用模座
assembly mark 铸造合模记号
back pouring 补浇注 backing sand背砂
base bullion 粗金属锭 base permeability 原砂透气度
belling 压凸 billet 坏料
bleed 漏铸 blocker 预锻模膛
blocking 粗胚锻件 blow hole 铸件气孔
board drop hammer 板落锤 bottom
pour mold 底浇
bottom pouring 底注 boxless mold脱箱砂模
break-off core 缩颈砂心 brick molding 砌箱造模法
buckle 剥砂面 camber 错箱camlachie cramp 铸包 cast blade铸造叶片
casting flange 铸造凸缘 casting on flat 水平铸造
chamotte sand 烧磨砂 charging hopper 加料漏斗
cleaning of casting 铸件清理
closed-die forging 合模锻造
core compound 砂心黏结剂 core template 砂心模板
core vent 砂蕊排气孔 corner gate 压边浇口
counter blow hammer 对击锻造
counter lock 止口镶嵌方式
depression 外缩凹孔 die approach模口角度
draw out 锻造拔长 draw plate 起模板
draw spike 起模长针 dummying 预锻
embedded core 加装砂心 erosion 冲砂
fettling 铸件清理 filling core 埋入砂心
filling in 填砂 film play 液面花纹
finishing slag 炼後熔渣 flash gutter锻模飞边槽
flask molding 砂箱造模 forging roll辊锻机
formboard 进模口板 gutter 锻模飞边槽
hammer man 锻工 heading machine顶镦机
impacter 卧式锻造机 inblock cast 整体铸造
ingot 铸锭 ingot blank 铸坯
inlay casting 镶铸法 investment casting 失模铸造
isothermal forging 恒温锻造 loose
piece 木模活块
molding pit 铸模地坑 pouring process 浇注法
recasting 重铸 roll forging 轧锻rolled surface 轧制表面 rough sand粗砂
roughing forge 粗锻 sand crushing塌箱
seamless forging 无缝锻造 separate分离
shave 崩砂 shrinkage fit 收缩配合
shut height 闭合高度 sieve mesh 筛孔
sintering of sand 铸砂烧贴 slag 熔渣
slag inclusion 夹渣 stickness 黏模性
strip layout 带状胚料排样法 tap
casting 顶注
top gate 顶注浇口 unworked casting不加工铸件
upender 翻转装置 upending 顶锻
uphill casting 底铸 white cast iron 白口铸件
模具加工方法
barrel 滚筒(加工) bending 波纹加工
broaching 拉刀切削 centering 定中心
cutting 切削 cylindrical lathe cutting外圆车削
electric discharge machine 放电加工
electrolytic grinding 电解研磨
embossing 压花加工 facing 面车削
filing 锉刀修润 hand finishing 手工修润
hemming 卷边加工 hobbing 滚齿加工
joggling 摇动加工 lapping 抛光/研磨修润
laser beam machining 雷射加工 lathe cutting 车床车削
planning 刨削加工 polishing 抛亮光
reaming 铰孔修润 rough machining粗切削
rounding 圆形加工 sawing 锯削
scaling 清除钢碇缺陷 shaping 成形加工
skiving 表面研磨 slotting 切缝切削
taper turning 锥度车削 thread cutting螺纹切削
ultrasonic machining 超音波加工 up cut milling 逆铣加工
学理实验与试验用语
air permeability test 透气性试验
austenitic steel 沃斯田铁钢
brinell hardness 布耐内尔硬度
brinell hardness test 布氏硬度试验
charpy impact test 夏比冲击试验
conical cup test 圆锥杯突试验
cup flow test 杯模式流动度试验 dart
drop impact test 落锤冲击试验
Elmendorf test 埃罗门多撕裂强度试验
environmental stress cracking test环境应力龟裂试验
ericessen test 埃留伸薄板拉伸试验
falling ball impact test 落球冲击试验
fatigue test 疲劳试验 ferrite 纯铁体
gantt chart 甘特图 heat cycle test 热循环试验
histogram 柱状图 hot bend test 热弯试验
izod impact test 埃左德冲击试验
loop tenacity 环结强度
martens heat distortion temperature test马顿斯耐热试验
martensite 马氏体 mullen bursting
strength tester 密廉式破裂强度试验机
nol ring test 诺尔环试验
Normal distribution 常态分配
ozone resistance test 抗臭氧试验
pareto diagram 柏拉图
peeling test 剥离试验 pinhole test 针孔试验机
rattler test 磨耗试验 rockweel
hardness test 洛氏硬度试验
rockweel hardness 洛氏威尔硬度
rolinx process 罗林克斯射出压缩成形法
rossi-peakes flow test 罗西皮克斯流
动试验 sampling inspection 抽样检查
scratch hardness 抗刮硬度 shore hardness 萧氏硬度
spiral flow test 螺旋流动试验 surface abrasion test 表面磨耗试验
taber abraser 泰伯磨耗试验机 tensile impact test 拉伸冲击试验
tensile strength 抗拉强度 tension test张力试验
thermal shock test 冷热剧变试验
torsion test 扭曲试验
ubbelohde viscometer 乌别洛德黏度计 vicat indentation test 维卡针压陷试验
Vickers hardness test 维氏硬度试验
warpage test 翘曲试验
weatherometer 人工老化试验机
weissenberg effect 威森伯格回转效应
砂轮用语
abrasive 砂轮 Al2O3 氧化铝
balance 平衡 bond 结合
borazon 氧化硼立方晶 buffing wheel抛光布轮
diamond 钻石 dresser 砂轮整修机
dressing 修整 endless grinding belt循环式研磨带
finishing allowance 加工余量 grain磨粒
grinding disc 研磨盘 jamp up 孔眼堵塞
mesh 网筛目 parameter 参数
resinoid grinding wheel 半树脂型砂轮 slitting 切缝量
vitrified 陶瓷的 wheel 旋转
机械设计及周边其他用语
assembly drawing 装配图 auto tool
change cycle 自动换刀时间周期
beam 横梁 bending moment 弯矩
bending stress 弯曲应力 bottoming底靠
buckling 纵弯曲 chamfering 去角斜切
channel 凹槽 chattering 颤动
check point 查核点 chip 切屑
chip conveyor 排屑输送机
coefficient of friction 摩擦系数
compact 小型的 cooling pipe 冷却管
coupon 试样胚 deflection 挠曲量
distortion 扭曲变形 draft taper 拔模锥度
draw out 拉拔 fit tolerance 配合公差
flexible rigidity 弯曲刚性 gas vent气孔
hatching 剖面线 heater cooler 加热器冷却装置
hook cavity 钩穴 inching 寸动
lug 凸缘 maintenance 维修保固
metallurgy 冶金学 notch effect 切口效果
out of roughness 真圆度 performance动作性能
pit 坑 plane strain 倒角应力
plug mill 蕊棒轧管机 repeated load重覆载荷
riveted joint ?钉接合 sand paper 砂纸
shift 偏移 shrink fit 热压配合
shrinkage hole 缩孔 sinking 凹陷
sketch 草图 spalling 剥落
straightness 直度 submarine 深陷式
surface roughness 表面粗度 tapping攻螺丝
thermocouple 热电耦 torsion load 扭转载荷
toughness 韧性 tracing 描图
under cut 凹割
业务与贸易关连用语
accept order 接受订货 account 帐户
after service 售后服务 amendment修正
annual sales 年销售额 at sight 见票即付
balance 余额 bank draft 汇票
bargain goods 廉价品 batch 批次
bid 出价 bid sales 投标买卖
bill of landing 提单 bills receivable应收票据
brand 品牌 bulk cargo 散装货
business transaction 商业交易 buyer买方
carbon copy 打字副本 cargo
collection 揽货
carton 纸箱 cash in advance 预付现金
catalogue 型录 cheque 支票
CLF 运费保险费在内价格 claim 索赔
clearance goods 清仓品 commision佣金
commission 批发商 complain 抱怨
container 货柜 correspondence bank往来银行
cost 成本 cost and freight; C&F 含运费价格
custom broker 报关行 customer 客户
D/A 承兑交单 D/P 付款交单
deferred payment 分期付款 deferred
shipment 分期装运
delivery on spot 当场交货 delivery time 交期
delivery order 交货单 discount 折扣
discount on draft 贴现 documentary draft跟单汇票
down payment 订金 enclosure 附件
endorsement 背书 enquete 调查
exhibition 展览会 export 出口
factory visiy 工厂参观 favorable price 合宜价格
foreign exchange 外汇 free on board船上交货价
idea price 希望价格 import 进口
Japanese Industrial 日本工业规格invoice 发票
L/C 信用状 margin 利润
market 市价 net weight 净重
no payment 拒绝付款 odd item 零头
offer 报价 open account 交互计算
order 订单 over looked 疏漏
packing 包装 pamphlet 小册子
partial shipment 分批装船 patent 专利
paying price 合算价格 payment method 付款方式
port of destination 目地港 port of trans-shipment 转口港
price 价格 price decending 减价
price rising 涨价 procurement 采办
prompt delivery 即时交货 purchase购入
purchasing agent 采购代理商
quotation 报价单
rebate 回扣 reference 查询
remittance 汇款 repeat order 追加订货
request letter 请求函 rumor 风评
second hand goods 二手货 shipper货主
shipping 装船 shipping mark 唛头
shipment 出货 sold out 卖完
sole agent 总代理商 special discount特别折扣
specification 规格 sample order 指样订货
standing 信用情形 storage charge 仓租
subcontract 外包 subject to final
confirmation 有待确认之报价
supplier 供应商 T/T 电汇
tie-in sale 搭售 trade fair 商展会
trans-shipment 转运 transferred 已转运
wharf 码头
A
3D coordinate measurement 三次元量床 3D modeling 三次元模拟
aberration 色差 abnormal glow 不规
则辉光放电
abrasive 砂轮 access 通路
account 帐户 accretion 炉瘤
accurate die casting 精密压铸 acid converter 酸性转炉
acid lining cupola 酸性熔铁炉 acid
open-hearth furnance 酸性平炉
activator 活化剂 acetylene 乙炔
adjustable spanner 活动扳手 aerator松砂机
after service 售後服务 age hardening时效硬化
ageing 老化处理 air hardening 气体硬化
airless plasting cleaning 离心喷光 air
patenting 空气韧化
air permeability test 透气性试验 air
set mold 常温自硬铸模
air vent valve 通气阀 all coremolding 集合式铸模
alloy tool steel 合金工具钢 all round die holder 通用模型
aluminium alloy 铝合金钢
amendment 修正
ampere 电流安培 anchor pin 锚梢
angle cutter 角铣刀 angle welding 角焊
angular pin 角梢 angular pin 倾斜梢
animation 卡通影片 anode effect 阳极效应
annealing 退火 annual sales 年
frame 床身机架 friction 摩擦
friction brake 摩擦煞车 gap shear 凹口剪床
gear 齿轮 gib 滑块引导部